Day: February 22, 2021

144690-92-6,Let¡¯s face it, organic chemistry can seem difficult to learn. Especially from a beginner¡¯s point of view. Like C48H44N6O6,introducing its new discovery.

A solution of MTT in an organic solvent and water (20%) was heated for 4-8 hrs at reflux. When the solvents were either acetonitrile (ACN), isopropyl alcohol (IPA) or t-butanol (t-BuOH), 1 volume of water was added, and the reaction was stirred until the amount of MTT was less than 2%. The mixture was evaporated to dryness. Ethyl acetate (EtOAc, 1 volume) was added to the residue and then evaporated again (twice). The resulting solid was dissolved in EtOAc (12 vol) and heated to reflux. The solution was cooled (2 C.) and stirred for 2 hrs. The product was filtered, washed (EtOAc, 1 vol), and dried on vacuum (45 C.). Table 1 shows the process details with different organic solvents: TABLE 1 Total solvent Time Solvent(s) Volume Temperature ( C.) (hrs) pH ACN:H2O 5:1 + 1 85 7 4.89-4.3 IPA:H2O 5:1 + 1 85 7 4.62-4.25t-BuOH:H2O 5:1 + 1 85 7 4.78-4.28n-propanol:H2O 5:1 reflux 2.5 4.3n-BuOH:H2O 5:1 110 2.5 4.412-BuOH:H2O 5:1 100 3 4.5iso-penthanol:H2O 5:1 100 3 5DMA:H2O 5:1 100 4 4.5DMF:H2O 5:1 100 4 4.5

Note that a catalyst decreases the activation energy for both the forward and the reverse reactions and hence accelerates both the forward and the reverse reactions.144690-92-6, you can also check out more blogs about144690-92-6

Reference£º
Patent; Hedvati, Lilach; Pilarsky, Gideon; Shenkar-Garcia, Natalia; US2006/148870; (2006); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6,is a common compound. C48H44N6O6In an article, once mentioned the new application about 144690-92-6.

To 3L reaction flask 165.3g above prepared 1 – [[[2- (triphenylmethyl) -2H- tetrazole-5-yl] biphenyl-4-yl] methyl] -2- propyl-4- (1-hydroxy-1-methylethyl) imidazole-5-carboxylic acid (5-methyl-2-oxo-1,3-dioxolen-4-yl) methyl ester ( compound ) and 1.90L70% acetic acid, mechanical stirring, heated to 50 , the reaction 2.5h, an ice bath was added 1.1L of water was stirred.Filtration, the filtrate with 300ml * 3 times extracted with methylene chloride, the methylene chloride phase 150mL ¡Á 5 times with 5% acetic acid solution was washed with acetic acid solution and extracted with 250ml of dichloromethane, and the combined organic phases.The solvent was distilled off under reduced pressure, the residue was added 380mL of ethyl acetate was heated with stirring and cooling to precipitate a solid.Suction filtered, the filter cake was dried in vacuo to give a white solid product to 89.6 g, weight yield was 77.8%.To a 1L reaction flask above 85g crude product olmesartan medoxomil, 420ml of tetrahydrofuran was heated at reflux, was added 360ml of ethyl acetate, the ice bath was stirred for crystallization.Filtration cake blast drying to constant weight to give the product as a white solid 74.8g, a yield of 83.5% by weight., 144690-92-6

The proportionality constant is the rate constant for the particular unimolecular reaction. the reaction rate is directly proportional to the concentration of the reactant. I hope my blog about 144690-92-6 is helpful to your research. 144690-92-6

Reference£º
Patent; Bengbu Tu Shan Fengyuan Pharmaceutical Co., Ltd.; Ma, Qisheng; Li, Baoqin; Sun, Peng; (18 pag.)CN105418593; (2016); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6,Let¡¯s face it, organic chemistry can seem difficult to learn. Especially from a beginner¡¯s point of view. Like C48H44N6O6,introducing its new discovery.

Example 2: preparation of olmesartan medoxomil (I) as per the present invention: To a mixture of acetic acid ( 37.5 ml) and water (12.5 ml) was added trityl olmesartan medoxomil (III) (10 g) and heated at 40-45 C for 2 hours. Water (12.5 ml) was added and the reaction mixture was filtered to remove trityl alcohol. The filtrate was subjected to agitated thin film dryer, wherein the feed rate was of about 4 to 10 ml per minute, heating medium was jacketed hot water at 45-50 C and vacuum was 70-75 mm/Hg. Crude olmesartan medoxomil (I) was recovered form ATFD. HPLC purity: olmesartan medoxomil (I) (97.81 %); olmesartan acid impurity (II) (0.97%). To acetone (40 ml) crude olmesartan medoxomil (I) was added, the slurry was heated at 54-58 C for 30 minutes and then stirred for 1 -2 hours at 0-5 C, the solid was filtered. Wet solid was added to acetone (120 ml) and heated at 55-60C. The solution was filtered. From the filtrate about 95 ml of acetone was distilled out at atmospheric pressure. The concentrated mass was stirred at 25-30 C for 8-12 hours and then at 0-5 C for 1 -3 hours. The solid was filtered, washed with acetone and dried. Yield 5.3 g (76.81 %). HPLC purity: olmesartan medoxomil (I) (99.67 %); olmesartan acid impurity (II) (0.07%).

Note that a catalyst decreases the activation energy for both the forward and the reverse reactions and hence accelerates both the forward and the reverse reactions.144690-92-6, you can also check out more blogs about144690-92-6

Reference£º
Patent; LUPIN LIMITED; FIRKE, Rajendra, Viswanath; SISODIA, Ujjwal,Komalsingh; BHANGALE, Chandrakant,Shriram; SHIVDAVKAR, Radhakrishna, Bhikaji; GODBOLE, Himanshu, Madhav; SINGH, Girij, Pal; WO2013/21312; (2013); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

37830-90-3,Let¡¯s face it, organic chemistry can seem difficult to learn. Especially from a beginner¡¯s point of view. Like C5H6O3,introducing its new discovery.

(1) 4-Bromomethyl-5-methyl-1,3-dioxolen-2-one [compound of formula (III) in which R is methyl and X is bromine] 3.42 g of 4,5-dimethyl-1,3-dioxolen-2-one [compound of formula (III’) in which R is methyl, prepared in accordance with the procedure described in Tetrahedron Letters, pages 1701-1704, (1972)] was dissolved in 150 ml of carbon tetrachloride. To the solution were added 5.34 g of N-bromosuccinimide and a catalytic amount of alpha,alpha’-azobisisobutyronitrile. The mixture was heated under reflux for 15 minutes. The reaction mixture was cooled with ice, and the insoluble materials were removed by filtration. The filtrate was concentrated under reduced pressure to give a syrupy residue. The residue was distilled under reduced pressure, and a fraction having a boiling point of 115¡ã to 120¡ã C./5 mmHg was recovered. Thus, 4.2 g (yield 73percent) of the captioned compound having the following properties was obtained as a colorless liquid. Elemental analysis for C5 H5 BrO3: IR (neat) nu(cm-1): near 18 25 (carbonyl). NMR (CCl4) delta(ppm): 2.10 (3H, –CH3, s), 4.10 (2H, –CH2 Br, s).

The proportionality constant is the rate constant for the particular unimolecular reaction. the reaction rate is directly proportional to the concentration of the reactant. I hope my blog about 37830-90-3 is helpful to your research. 37830-90-3

Reference£º
Patent; Kanebo Ltd.; US4448769; (1984); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

In an article, published in an article,once mentioned the application of 80841-78-7,molecular formula is , is a conventional compound. this article was the specific content is as follows. 80841-78-7

Example 2; 36.0 g (50.3 mmol) ethyl 4-(l -hydroxy- 1-methy lethyl)-2-propy 1-1- {4-[2-(trityltetrazol-5-y I)- phenyl]phenyl} -methyl imidazole-5-carboxylate (Va) and 3.0 g (75.4 mmol) of NaOH were suspended in 413 ml dimethylacetamide. The suspension was then stirred at room temperature for 20 h and after that 6.9 g (50.3 mmol) of K2CO3, were added. The mixture was cooled to 00C and solution of 15.4 g (70.4 mmol) 4-chloromethyl-5-methyl-2-oxo-l,3- dioxolene in 39 ml of dimethylacetamide were slowly added. The mixture was slowly heated to 500C and stirred at this temperature for 2 h. After esterification was completed, the mixture was cooled to 10 0C and poured into a mixture of 625 ml of ethyl acetate and 625 ml of 10 % NaCl, and stirred at 25 0C for 15 min. The phases were separated and organic phase was washed 2chi with 500 ml of 10 % NaCl, dried over Na2SO4 and filtered. The filtrate was concentrated up to 14 (approximately 270 g) at reduced pressure.To the resulting solution, 80 ml of ethanol and 8.3 ml (100 mmol) of cone. HCl were added EPO and stirred at 24-26C for 3h. To the cooled mixture 600 ml of water was added and pH of the suspension was estimated to 5 by addition of 5 M NaOH. The phases were stirred for 15 min and separated. Water phase was reextracted with 150 ml of ethyl acetate. Collected organic phases were dried over Na2SO4, filtered and concentrated under reduced pressure. 560 ml of ethyl acetate were added and the mixture was evaporated again. After that, 300 ml of ethyl acetate were added and the mixture was cooled to 20 0C and stirred for Ih, filtered off and washed with 20 ml of fresh ethyl acetate. The yield of the product (I) was 21 g (75 %).

The proportionality constant is the rate constant for the particular unimolecular reaction. the reaction rate is directly proportional to the concentration of the reactant. I hope my blog about 80841-78-7 is helpful to your research. 80841-78-7

Reference£º
Patent; KRKA; WO2007/17135; (2007); A2;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

In an article, published in an article,once mentioned the application of 80841-78-7,molecular formula is , is a conventional compound. this article was the specific content is as follows. 80841-78-7

To a solution of the compound of Formula IV (5.0 g) in toluene (40 mL), dimethylacetamide (10 mL) is added, followed by addition of sodium hydroxide (1.2 g) and N,N-diisopropylamine (3.7 g) at 25-35C. The mixture is stirred at 40- 45C for 4 hours. 5-Methyl-2-oxo-(1 ,3-dioxolene-4-yl)methyl chloride (1.5 g) and tetrabutylammonium bromide (0.5 g) are added at 40-450C. The mixture is stirred at 60-70C for 8 hours. The mass is cooled to 25-35C, water (50 mL) is added, and the pH is adjusted to about 6-7 by adding 10% aqueous HCI. The layers are separated. The aqueous layer is extracted with toluene (25 mL). The organic layers are combined and washed with water (25 mL). The solvent is distilled under reduced pressure. Methanol (25 mL) is added to the residue. The mixture is cooled to 0-50C and stirred at that temperature for 45 minutes. The formed solid is filtered, washed with methanol (10 mL) and dried for 45 minutes under vacuum (yield 3.0 g).

Note that a catalyst decreases the activation energy for both the forward and the reverse reactions and hence accelerates both the forward and the reverse reactions.80841-78-7, you can also check out more blogs about80841-78-7

Reference£º
Patent; DR. REDDY’S LABORATORIES LTD.; DR. REDDY’S LABORATORIES, INC.; KOLLA, Naveen Kumar; MANNE, Nagaraju; NAREDLA, Anitha; SHINDE, Sachin Gulabrao; WO2011/14611; (2011); A2;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6,is a common compound. C48H44N6O6In an article, once mentioned the new application about 144690-92-6.

1L glass reaction flask was added with 500ml of 75% acetic acid, 100.0g of intermediate 2 was added with stirring, and the mixture was heated to stirAfter 45-55 C, after 2 hours of incubation, reduce the temperature to 20-30 C, add 125ml of water, stir for 30 minutes, filter, filter cake with 100ml of 75% acetic acid, transfer the filtrate to 3L glass reaction bottle, The filtrate was successively added with 1000 ml of dichloromethane and 1000 ml of water, and the mixture was stirred and the organic layer was temporarily stored. The aqueous layer was extracted with 500 ml of dichloromethane, and the organic layer was combined. The organic layer was washed with 1000 ml of water, and the organic layer was washed with 5% carbonic acid. The aqueous sodium hydrogen solution was adjusted to rhoEta=6.0~7.0 (about 600 ml), and the organic layer was washed with 500 ml of water, and the organic layer was separated. The organic layer was concentrated under reduced pressure at 30-40 C until no significant solvent was discharged, and 300 ml was added. Ethyl acetate was stirred and crystallized at 20-30 C for 1 hour, filtered, and the filter cake was rinsed with 300 ml of ethyl acetate. The filter cake was blast dried at 40-50 C for 8 hours to obtain a white solid 60.0 g. (product), yield 86.0%, HPLC: 99.0%.

Enzymes are biological catalysts that produce large increases in reaction rates and tend to be specific for certain reactants and products. I hope my blog about 144690-92-6 is helpful to your research. 144690-92-6

Reference£º
Patent; Jiashi (Hunan) Pharmaceutical Technology Co., Ltd.; Dai Yongzhi; Liu Hu; Zhu Laifa; Cai Jian; (8 pag.)CN108341804; (2018); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

80841-78-7,Chemistry can be defined as the study of matter and the changes it undergoes. You¡¯ll sometimes hear it called the central science because it is the connection between physics and all the other sciences, starting with biology.4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one,introducing its new discovery.

130 ml of N,N-dimethylacetamide, 14.0 g (20 mmol) of ethyl 4-(2-hydroxypropan-2-yl)-2-propyl-1-((2′-(1-trityl-1H-tetrazol-5-yl)biphenyl-4-yl)methyl)-1H-imidazole-5-carboxylate and 2.2 g (16 mmol) of KOH were charged into reaction vessel at room temperature under inert atmosphere. The mixture was stirred at room temperature for 2 h, and then the sample of reaction mixture was analysed (HPLC; starting material 0.2 %, hydrolysed starting material 98.11 %). Then 3.0 g (2.2 mmol) of potassium carbonate powder and 1.4 g (8.4 mmol) of potassium iodide were added. The reaction mixture was cooled to 0 C and 5.0 g (33 mmol) of 4-(chloromethyl)-5-methyl-1,3-dioxol-2-one was added at 0 to 5C. After the addition, the reaction mixture was warmed to 40-45 C within one hour, then the mixture was stirred at this temperature for 2h. The sample of reaction mixture was analysed (HPLC; tritylolmesartan medoxomil 97.22 %, 4-(2-hydroxypropan-2-yl)-2-propyl-1-((2′-(1-trityl-1H-tetrazol-5-yl)biphenyl-4-yl)methyl)-1H-imidazole-5-carboxylate 0.09 %). The mixture was cooled to 10 to 20 C and then 250 ml of ethyl acetate was added. The mixture was cooled again to 5-10 C and then 200 ml of 10 % NaCl was added slowly. The temperature should not be higher than 25 C during the addition. The phases were mixed separated and organic phase was washed with 100 ml of 10 % NaCl (2*) and dried over anhydrous sodium sulphate. After the filtration filtrate was evaporated under reduced pressure at temperature under 45C to oily residue. To the residue 30 ml of acetonitrile was added at temperature not more than 45C. The mixture was stirred at this temperature for 10 minutes then was cooled to 20 to 25C and stirred at this temperature for 0.5 h and after that 3h at 0 to 5C. The suspension was filtered, the cake washed with cold acetonitrile and dried at 40 to 50C. Yield: 17.0 g (94%) HPLC: 99.72 % of the product, all impurities are under 0.1%. IR: 3408, 1818, 1805, 1741, 1681, 1529, 1147, 1003, 699 XRD:

Do you like my blog? If you like, you can also browse other articles about this kind. Thanks for taking the time to read the blog about 80841-78-7

Reference£º
Patent; Krka Tovarna Zdravil, D.D., Novo Mesto; EP2334668; (2011); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6,Let¡¯s face it, organic chemistry can seem difficult to learn. Especially from a beginner¡¯s point of view. Like C48H44N6O6,introducing its new discovery.

Trityl olmesartan medoxomil (8 g, 10 mmol) is dissolved in THF (50 ml) and 48 % aqueous hydrobromic acid (3.5 ml, 30 mmol) is added. The mixture is stirred for 1 hour at room temperature and then 1 hour at 0 C. The precipitate is filtered, washed with cold THF (20 ml) and dried overnight in vacuum at room temperature to give 5.7 g of olmesartan medoxomil hydrobromide Form B (98.6 % area)

Enzymes are biological catalysts that produce large increases in reaction rates and tend to be specific for certain reactants and products. I hope my blog about 144690-92-6 is helpful to your research. 144690-92-6

Reference£º
Patent; LEK Pharmaceuticals d.d.; EP2022790; (2009); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6,Let¡¯s face it, organic chemistry can seem difficult to learn. Especially from a beginner¡¯s point of view. Like C48H44N6O6,introducing its new discovery.

A solution of MTT in an organic solvent and water (20%) was heated for 4-8 hrs at reflux. When the solvents were either acetonitrile (ACN), isopropyl alcohol (IPA) or t-butanol (t-BuOH), 1 volume of water was added, and the reaction was stirred until the amount of MTT was less than 2%. The mixture was evaporated to dryness. Ethyl acetate (EtOAc, 1 volume) was added to the residue and then evaporated again (twice). The resulting solid was dissolved in EtOAc (12 vol) and heated to reflux. The solution was cooled (2 C.) and stirred for 2 hrs. The product was filtered, washed (EtOAc, 1 vol), and dried on vacuum (45 C.). Table 1 shows the process details with different organic solvents: TABLE 1 Total solvent Time Solvent(s) Volume Temperature ( C.) (hrs) pH ACN:H2O 5:1 + 1 85 7 4.89-4.3 IPA:H2O 5:1 + 1 85 7 4.62-4.25t-BuOH:H2O 5:1 + 1 85 7 4.78-4.28n-propanol:H2O 5:1 reflux 2.5 4.3n-BuOH:H2O 5:1 110 2.5 4.412-BuOH:H2O 5:1 100 3 4.5iso-penthanol:H2O 5:1 100 3 5DMA:H2O 5:1 100 4 4.5DMF:H2O 5:1 100 4 4.5

I hope this article can help some friends in scientific research. I am very proud of our efforts over the past few months and hope to 144690-92-6, help many people in the next few years.C48H44N6O6

Reference£º
Patent; Hedvati, Lilach; Pilarsky, Gideon; Shenkar-Garcia, Natalia; US2006/148870; (2006); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem