Month: February 2021

80841-78-7,is a common compound. C5H5ClO3.In an article, once mentioned the new application about 80841-78-7.

Step B, go to the reaction solution of compound (II) obtained in Step A with stirring,Add 6.27kg of anhydrous sodium carbonate powder and 2.01kg of iodine, replace the air with nitrogen,The nitrogen pressure in the kettle is ?0.01Mpa, the control temperature is 50 ¡À 2 ,15.05 kg of compound (IV) was added dropwise at a constant pressure, and the addition was completed within 40 to 60 minutes.After the reaction was held for 1 hour, the reaction mixture was reduced to below 10 C.Extract with conventional solvents in an extraction kettle, wash with water, and separate the layers.The organic phase was distilled under reduced pressure to recover the solvent, crystallized, centrifuged,After drying, 54.88 kg of the crude compound (I) was obtained.Step C: Add 192.08 kg of ethyl acetate to the 500L refining kettle, start stirring,Add 54.88 kg of crude compound (I) obtained in step B, close the feed port,Keep the pressure ?0.01MPa after replacing air with nitrogen,The temperature was raised to 75 C and dissolved for 25 minutes until it was clear. The filtrate was filtered and the temperature was reduced to 2.5 C.Centrifuge, put the filter cake into the double cone dryer,Under reduced pressure, a small flow of nitrogen was passed in for replacement three times, and the drying temperature was controlled to 40-50 C.Vacuum degree ?-0.09MPa, after drying for 1 hour,Increase the drying temperature to 50 60 and continue drying for 3 hours.After cooling down, 53.60 kg of compound (1) was obtained, and the HPLC content was 99.87%.Compound (III) had a residual content of 0.06%.

The catalyzed pathway has a lower Ea, but the net change in energy that results from the reaction is not affected by the presence of a catalyst. In my other articles, you can also check out more blogs about 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one.C5H5ClO3

Reference£º
Patent; Shandong Xinhua Pharmaceutical Co., Ltd.; Zhu Lianbo; Wu Hui; Dou Guohua; (6 pag.)CN110590758; (2019); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

In an article, published in an article,once mentioned the application of 144690-92-6,molecular formula is , is a conventional compound. this article was the specific content is as follows. 144690-92-6

A solution of MTT in 10 volumes of acetic acid (75%) was heated for 1.5 hrs at 60 C. until a pH of 2.21-2.23 was achieved, and the reaction was stirred until the amount of MTT was less than 2%. The mixture was evaporated to dryness. Ethyl acetate (EtOAc, 1 volume) was added to the residue and then evaporated again (twice). The resulting solid was dissolved in EtOAc (12 vol) and heated to reflux. The solution was cooled (2 C.) and stirred for 2 hrs. The product was filtered, washed (EtOAc, 1 vol), and dried on vacuum (45 C.)., 144690-92-6

Because enzymes can increase reaction rates by enormous factors and tend to be very specific, typically producing only a single product in quantitative yield,they are the focus of active research.144690-92-6, you can also check out more blogs about144690-92-6

Reference£º
Patent; Hedvati, Lilach; Pilarsky, Gideon; Shenkar-Garcia, Natalia; US2006/148870; (2006); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

In heterogeneous catalysis, the catalyst is in a different phase from the reactants. 144690-92-6, At least one of the reactants interacts with the solid surface in a physical process called adsorption in such a way. 144690-92-6, name is C48H44N6O6. In an article£¬Which mentioned a new discovery about 144690-92-6

To 12.0g (15 mmol) of tritylolmesartan medoxomil prepared according to examples 1 or 2 69 ml of ethyl acetate was added and after that 12 ml of methanol and 2.67 ml (32 mmol) of conc. HCl were added. The mixture was stirred at room temperature for 2h and then the mixture was cooled to below 2C. To the cooled mixture 71 ml of 1% NH3 was slowly added to adjust pH to 4.93. The phases were separated and water phase was reextracted with 20 ml of ethyl acetate. Collected organic phases were dried over Na2SO4, filtered and concentrated under reduced pressure to approximately 15g of oily residue. To this residue 15 ml of ethyl acetate were added and the mixture was cooled to 20 C and stirred at this temperature for 2h, and then cooled under 0C and stirred at this temperature for 1hour. The product was filtered off and washed with 5 ml of fresh ethyl acetate and dried. Yield: 7.55 g (90%). HPLC: 99.81 % of the product, all individual impurities under 0.10%.

The catalyzed pathway has a lower Ea, but the net change in energy that results from the reaction is not affected by the presence of a catalyst. In my other articles, you can also check out more blogs about Triphenyl methyl olmesartan.C48H44N6O6

Reference£º
Patent; Krka Tovarna Zdravil, D.D., Novo Mesto; EP2334668; (2011); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

In an article, published in an article,once mentioned the application of 144690-92-6,molecular formula is , is a conventional compound. this article was the specific content is as follows. 144690-92-6

To the three-necked flask were added with 38 ml of ethyl acetate, 45 g of 6.4% dilute hydrochloric acid, 25 g of trityl olmesartan medoxomil was added with stirring. Stir in water bath, control the temperature 15 to 20 C, stirring about 4 hours, TLC plate detection point of raw material disappeared,That is, it is judged that the deprotection reaction is completed.Cooled to room temperature, 115 ml * 5 toluene was added to wash, the aqueous layer was added with 135 ml of acetone, potassium bicarbonate aqueous solution adjusted P=4.0, control temperature 15 ¡À 5 C Stir for 2 hours, Filtered and dried to give 16.0 g of olmesartan medoxomil in a yield of 90.2%. HPLC analysis: purity 98.75%, impurity a (olmesartan acid) 0.71%, individual impurities less than 0.10%

Interested yet? Keep reading other articles of 144690-92-6!, 144690-92-6

Reference£º
Patent; Zhejiang Huahai Pharmaceutical Co., Ltd,; Huang, Xiangliang; Zhang, LI; Hua, yuanyuan; Wu, Yong De; (7 pag.)CN102584804; (2016); B;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

Chemistry is the experimental and theoretical study of materials on their properties at both the macroscopic and microscopic levels. 144690-92-6. In a patent£¬Which mentioned a new discovery about 144690-92-6, molcular formula is C48H44N6O6, introducing its new discovery.

Example 5; Olmesartan medoxomil (V); Water (10 g) was added to a solution of the starting substance (III; 20 g) in acetonitrile (50 ml), and the mixture was heated to a mild boil for 14 h. Acetonitrile was evaporated, and, after dissolving in acetone (150 ml), the mixture was filtered through alumina and concentrated. After crystallization from the mixture tetrahydrofuran / ethyl acetate H g (78 %) of the product with an HPLC purity of 97.0 % was obtained. Recrystallization from methanol and water gave 1O g of the product with an HPLC purity of 99.3 %; m.p. 175- 177 0C.; Example 6; Olmesartan medoxomil (V); Water (10 g) was added to a solution of the starting substance (III; 10 g) in acetonitrile (50 ml), and the mixture was heated to a mild boil for 14 h. Acetonitrile was evaporated, and, after dissolving in acetone (150 ml), the mixture was filtered through silica gel and concentrated. After crystallization from acetonitrile, 4 g (57 %) of the product was obtained. After recrystallization from the mixture methyl tert-butyl ether / ethyl acetate, 3.4 g of the product with an HPLC purity of 99.4 % was obtained; m.p. 175-177 C.

Enzymes are biological catalysts that produce large increases in reaction rates and tend to be specific for certain reactants and products. I hope my blog about 144690-92-6 is helpful to your research. 144690-92-6

Reference£º
Patent; ZENTIVA, A.S.; WO2007/48361; (2007); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

In an article, published in an article,once mentioned the application of 80841-78-7,molecular formula is , is a conventional compound. this article was the specific content is as follows. 80841-78-7

A solution containing about 46 g of compound 4 was taken, 3.5g sodium iodide was added, 280 mL N, N-dimethylformamide, 11.2g DMDO-Cl was slowly added dropwise, 30 Minute addition is completed. After dropping, Heated to 55 , Reaction for 7 hours, The reaction is completely over. filter, Remove insolubles, The filtrate was poured into 700mL of water, Extraction with ethyl acetate, The ethyl acetate layer was collected, dry, filter, The filtrate is concentrated. To the oily substance obtained after the concentration was added 200 mL of ethanol, Stirring, A white solid precipitation, Collect the solid, Washed with 50mL cyclohexane beating, 45.0 g of product was obtained, Two-step total yield of 80.6% The purity of the product was 98% by HPLC.

I hope this article can help some friends in scientific research. I am very proud of our efforts over the past few months and hope to 80841-78-7, help many people in the next few years.C5H5ClO3

Reference£º
Patent; Disha Pharmaceutical Group Co., Ltd.; Zhang Zhaoxing; Zhang Hongqiang; Qin Litai; Li Wei; Li Zongwen; Xia Haijian; (6 pag.)CN103012382; (2016); B;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

80841-78-7,Enzyme inhibitors cause a decrease in the reaction rate of an enzyme-catalyzed reaction by binding to a specific portion of an enzyme and thus slowing or preventing a reaction from occurring. Which mentioned a new discovery about 80841-78-7.

10L autoclave, 520g (0.75mol) Compound 5, DMF3kg, potassium carbonate and 215.3g (1.6mol), stirred at room temperature 1.5-2.5h added to the system after 63.0g (0.38mol) of potassium iodide was added dropwise while – Chloromethyl -5-methyl-1,3-dioxol-2-one 40.0g (0.94mol). Dropping was completed, the reaction at room temperature after 3-4h TLC or HPLC in control, raw reaction was complete. To the system was added ethyl acetate and 3L 3L water and 200g of sodium chloride, stirring separated and the aqueous layer was washed with 3X1L ethyl acetate, the combined organic layers, the organic layer was dried, filtered and the solvent was evaporated cooling is added 0-10 , methanol was added 1600g beating 30min, filtered, then the filter cake was slurried at room temperature in acetonitrile 1600g 30min, filtered to afford intermediate 6 about 553.8g,

Enzymes are biological catalysts that produce large increases in reaction rates and tend to be specific for certain reactants and products. I hope my blog about 80841-78-7 is helpful to your research. 80841-78-7

Reference£º
Patent; Jiangsu Bang Pharmaceutical Co., Ltd.; Zhao, Guangrong; Huan, Shuang; Zhao, Huayang; Liu, Liping; Chen, Guoping; Tang, Jingyu; (19 pag.)CN105481842; (2016); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6,is a common compound. C48H44N6O6.In an article, once mentioned the new application about 144690-92-6.

7.5 cm in diameterIn a 500 mL four-necked flask equipped with two stirring blades,40 g of trityl olmesartan medoxomil,180 ml of acetic acid,40 g (1.0 volume) of water was added,The mixture was stirred at 40 C. for 2 hours to carry out deprotection reaction (reaction conversion: 98.4%Olmesartan medoxomil purity: 98.95%,Olmesartan dimer: 0.047%).Then,The reaction solution was cooled to 20 C.,80 g of water was added,After stirring at 20 C. for 1 hour,The precipitated triphenylmethanol was removed by vacuum filtration,To the obtained filtrate, 240 ml of 10% sodium hydrogen carbonate was added,The liquidity of the aqueous layer was adjusted to pH 3.5,After adding 400 ml of ethyl acetate and vigorously stirring,The aqueous layer was separated,An organic layer containing olmesartan medoxomil was obtained (olmesartan medoxomil purity: 99.35%Dimer: 0.011%).200 ml of ethyl acetate was distilled off from the organic layer,After stirring at 20 to 30 C. for 1 hour,The precipitated solid was collected by filtration under reduced pressure as a wet body.The obtained wet body was dried at 40 C. for 14 hours,24 g of crystals of olmesartan medoxomil were obtained (yield: 86%, olmesartan medoxomil purity: 99.71%, dimer: 0.010%).

The catalyzed pathway has a lower Ea, but the net change in energy that results from the reaction is not affected by the presence of a catalyst. In my other articles, you can also check out more blogs about Triphenyl methyl olmesartan.C48H44N6O6

Reference£º
Patent; Tokuyama Corporation; Mori, Hiroshi; Tanaka, Kenji; (12 pag.)JP6091339; (2017); B2;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6,is a common compound. C48H44N6O6.In an article, once mentioned the new application about 144690-92-6.

A mixture of trityl olmesartan medoxomil in acetic acid and water (1:1, 400 mL) and sulfuric acid (12.2 gm) (1 mol equivalent) was stirred at 25C-30C for 45-60 minutes. Triphenylcarbinol was filtered and the filtrate was washed with acetic acid and water mixture (1:1, 50 rnL). Sodium carbonate solution (25% w/v, 100 mL) was charged to the filtrate and the product was extracted with dichloromethane (500 mL) followed by recovery of the solvent. The product was isolated, recrystallized using acetonitrile (300 mL), filtered, washed and dried under reduced pressure to obtain crude olmesartan medoxomil.Yield: 90% HPLC purity: 99.29 % OLM-acid: Not Detectable OLM- Eliminate: 0.07% Acetic acid content: Not Detectable

The catalyzed pathway has a lower Ea, but the net change in energy that results from the reaction is not affected by the presence of a catalyst. In my other articles, you can also check out more blogs about Triphenyl methyl olmesartan.C48H44N6O6

Reference£º
Patent; RANBAXY LABORATORIES LIMITED; KAPOOR, Ashwini, Kumar; MEHTA, Hiten, Sharadchandra; NATH, Asok; PRASAD, Mohan; WO2010/134052; (2010); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

80841-78-7,Enzyme inhibitors cause a decrease in the reaction rate of an enzyme-catalyzed reaction by binding to a specific portion of an enzyme and thus slowing or preventing a reaction from occurring. Which mentioned a new discovery about 80841-78-7.

To the flask was added 2000 g of acetone, 160 g of ethyl 4- (1-hydroxy-1-methylethyl) -2-propylimidazole-5-carboxylate (II), 150 g of K2CO3, 460 g of 4- [2- (Trityltetrazol-5-yl) phenyl] benzyl bromide (III), 20g KI, the temperature was raised to reflux, the reaction was incubated for 34-38 hours under stirring.Then add 102g KOH, reflux reaction 6 ~ 8h. Cool to 10 ~ 20 , add 170g DMDO-Cl, incubated for 30 ~ 60min.Heating to reflux, the reaction 22 to 26 hours.After the reaction was added 40g of diatomaceous earth, stirring for 30 to 60 minutes, suction filtration, 200g acetone rinse cake. To the filtrate was added 800g of drinking water and 200g of refined hydrochloric acid, the reaction at room temperature for 2 to 4 hours, filtered to remove by-product triphenylcarbinol. Dropping 10% K2CO3 aqueous solution, adjusting feedstock pH to 4, cooling to 10 ~ 20 , stirring crystallization 2h, filtration, the filter cake with a mixture of pre-cooled 45g acetone and 230g of drinking water washing and drying, to obtain Olmesartan Medoxomil 309 g, total yield 83.1% (relative to ethyl-4- (1-hydroxy-1-methylethyl) -2-propylimidazole-5- carboxylate (II)), purity: 99.27% of the main peak, 0.08% of the olmesartan acid, 0.14% of the triphenylmethanol, and 0.13% of the largest unidentified one.

One of the oldest and most widely used commercial enzyme inhibitors is aspirin, which selectively inhibits one of the enzymes involved in the synthesis of molecules that trigger inflammation. you can also check out more blogs about 80841-78-7.C5H5ClO3

Reference£º
Patent; Zhejiang Huahai Zhicheng Pharmaceutical Co., Ltd.; Zhejiang Huahai Pharmaceutical Co., Ltd.; Jin Congyang; Wang Jiquan; Zhang Wenling; Wang Peng; (10 pag.)CN107311990; (2017); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem