Day: October 22, 2020

In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact.37830-90-3, 4,5-Dimethyl-1,3-dioxol-2-one it is a common compound, a new synthetic route is introduced below.37830-90-3

(1) Synthesis of 4-bromomethyl-5-methyl-1,3-dioxolen-2-one[the compound of formula (III) in which X is a bromine atom]: 3.42 g of 4,5-dimethyl-1,3-dioxolen-2-one (synthesised in accordance with Tetrahedron Letters, (1972), pages 1701-1704) was dissolved in 150 ml of carbon tetrachloride, and 5.34 g of N-bromosuccinimide and a catalytic amount of alpha,alpha’-azobisisobutyronitrile were added. The mixture was heated under reflux for 15 minutes. The reaction mixture was concentrated to half of its volume and the resulting insoluble matter was removed by filtration. Concentrating the filtrate gave a syrupy residue. The residue was distilled under reduced pressure to give a fraction boiling at 115¡ã to 120¡ã C./5 mm Hg which was 4.2 g (yield 73percent) of the captioned compound., 37830-90-3

Chemical properties determine the actual use. Each compound has specific chemical properties and uses. We look forward to more synthetic routes in the future to expand 4,5-Dimethyl-1,3-dioxol-2-one reaction routes.

Reference£º
Patent; Kanebo Ltd.; US4455310; (1984); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact.37830-90-3, 4,5-Dimethyl-1,3-dioxol-2-one it is a common compound, a new synthetic route is introduced below.37830-90-3

EXAMPLE 1 Preparation of 4-chloro-4-methyl-5-methylene-1,3-dioxolane-2-one (III) To a solution of 50 g of 4,5-dimethyl-1,3-dioxolene-2-one (IV)(Synthesised by the method described in Tetrahedron Letters, 1701-1704 (1972)) in 350 ml of methylene chloride was added 65 g of sulfuryl chloride dropwise over 1 hour at 40¡ã-42¡ã C. The mixture was stirred for one hour at the same temperature and then evaporated in vacuo to remove the solvent. The resulting residue was distilled in vacuo to obtain 42.1 g (65percent of theory) of 4-chloro-4-methyl-5-methylene-1,3-dioxolane-2-one (III) as a colorless oil. B.p. 45¡ã-48¡ã C./2 mmHg. IR(CHCl3)nu(cm-1): 1820, near 1695 etc. NMR(CDCl3, delta(ppm)): 2.19(3H, s, CH3), STR5

Chemical properties determine the actual use. Each compound has specific chemical properties and uses. We look forward to more synthetic routes in the future to expand 4,5-Dimethyl-1,3-dioxol-2-one reaction routes.

Reference£º
Patent; Kanebo, Ltd.; US4554358; (1985); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”144690-92-6

Into a 1000 mL four-necked flask equipped with a two-piece stirring blade having a diameter of 10 cm,50 g of trityl olmesartan medoxomil, 225 ml of acetic acid and 75 ml of water were added and stirred at 40 C. for 2 hours to carry out deprotection reaction.Subsequently, the reaction solution was cooled to 20 C. and stirred at 20 C. for 1 hour, and the precipitated triphenylmethanol was removed by vacuum filtration,To the obtained filtrate were added 250 ml of 10% sodium hydrogen carbonate and 500 ml of ethyl acetate, followed by vigorous stirring, and the aqueous layer was separated to obtain an organic layer containing olmesartan medoxomil.200 ml of ethyl acetate was distilled off from the organic layer, and the mixture was stirred at 20 to 30 C. for 1 hour. The precipitated solid was collected by filtration under reduced pressure as a wet body.The obtained wet body was dried at 40 C. for 14 hours to obtain 30 g of crystals of olmesartan medexomil (purity: 99.54%)., 144690-92-6

As the rapid development of chemical substances, we look forward to future research findings about 144690-92-6

Reference£º
Patent; TOKUYAMA CORPORATION; MORI, HIROYUKI; TANAKA, KENJI; (11 pag.)JP2015/74608; (2015); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”144690-92-6

A solution of MTT in an organic solvent and water (20%) was heated for 4-8 hrs at reflux. When the solvents were either acetonitrile (ACN), isopropyl alcohol (IPA) or t-butanol (t-BuOH), 1 volume of water was added, and the reaction was stirred until the amount of MTT was less than 2%. The mixture was evaporated to dryness. Ethyl acetate (EtOAc, 1 volume) was added to the residue and then evaporated again (twice). The resulting solid was dissolved in EtOAc (12 vol) and heated to reflux. The solution was cooled (2 C.) and stirred for 2 hrs. The product was filtered, washed (EtOAc, 1 vol), and dried on vacuum (45 C.). Table 1 shows the process details with different organic solvents: TABLE 1 Total solvent Time Solvent(s) Volume Temperature ( C.) (hrs) pH ACN:H2O 5:1 + 1 85 7 4.89-4.3 IPA:H2O 5:1 + 1 85 7 4.62-4.25t-BuOH:H2O 5:1 + 1 85 7 4.78-4.28n-propanol:H2O 5:1 reflux 2.5 4.3n-BuOH:H2O 5:1 110 2.5 4.412-BuOH:H2O 5:1 100 3 4.5iso-penthanol:H2O 5:1 100 3 5DMA:H2O 5:1 100 4 4.5DMF:H2O 5:1 100 4 4.5

The chemical industry reduces the impact on the environment during synthesis, Triphenyl methyl olmesartan, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; Hedvati, Lilach; Pilarsky, Gideon; Shenkar-Garcia, Natalia; US2006/148870; (2006); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”144690-92-6

Example 8; To a solution of (5-Methyl-2-oxo-1,3-dioxolen-4-yl)methyl-4-(1-hydroxy-1-methyl ethyl)-2-propyl-1-{4-[2-(trityltetrazol-5-yl)phenyl]phenyl}methylimidazole-5-carboxylate (5.0 g; 6.25 mmol) and toluene (20 ml) at 15-20 C. is added hydrochloric acid (30 ml). Reaction mass is stirred at 15-20 C. for about 15 minutes to 4 hours. The reaction is monitored by TLC. After completion of reaction layers are separated. Aqueous layer is washed with toluene (10 ml). Adjusted the pH of the aqueous layer to 5-6 using aqueous potassium carbonate solution (200 ml) and the compound is extracted using ethyl acetate (60 ml). Combined ethyl acetate layers are washed with brine. Finally crude product (3.1 g; 89.8%) is isolated by evaporation of solvent under reduced pressure.Purity: 99.5%

With the complex challenges of chemical substances, we look forward to future research findings about Triphenyl methyl olmesartan,belong Dioxole compound

Reference£º
Patent; Ramanjaneyulu, Gorantla Seeta; Mohan, Bandari; Ray, Purna Chandra; Sethi, Madhuresh Kumar; Rawat, Vijendra Singh; Krishna, Yerramalla Raja; Lakshminarayana, Vemula; Srinivas, Mamidi; US2009/281327; (2009); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

Triphenyl methyl olmesartan, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”144690-92-6

To 12.0g (15 mmol) of tritylolmesartan medoxomil prepared according to examples 1 or 2 69 ml of ethyl acetate was added and after that 12 ml of methanol and 2.67 ml (32 mmol) of conc. HCl were added. The mixture was stirred at room temperature for 2h and then the mixture was cooled to below 2C. To the cooled mixture 71 ml of 1% NH3 was slowly added to adjust pH to 4.93. The phases were separated and water phase was reextracted with 20 ml of ethyl acetate. Collected organic phases were dried over Na2SO4, filtered and concentrated under reduced pressure to approximately 15g of oily residue. To this residue 15 ml of ethyl acetate were added and the mixture was cooled to 20 C and stirred at this temperature for 2h, and then cooled under 0C and stirred at this temperature for 1hour. The product was filtered off and washed with 5 ml of fresh ethyl acetate and dried. Yield: 7.55 g (90%). HPLC: 99.81 % of the product, all individual impurities under 0.10%.

The chemical industry reduces the impact on the environment during synthesis, Triphenyl methyl olmesartan, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; Krka Tovarna Zdravil, D.D., Novo Mesto; EP2334668; (2011); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact.37830-90-3, 4,5-Dimethyl-1,3-dioxol-2-one it is a common compound, a new synthetic route is introduced below.37830-90-3

PREPARATION 1 4-Bromomethyl-5-methyl-2-oxo-1,3-dioxole To a stirred solution of 3.0 g of 4,5-dimethyl-2-oxo-1,3-dioxole in 100 ml of carbon tetrachloride was added 4.63 g of N-bromosuccinimide. The resulting solution was heated under reflux and irradiated for 15 minutes. The reaction mixture was cooled to 0¡ã-5¡ã C., filtered and evaporated to give the title product. The NMR spectrum (CDCl3) showed absorptions at 2.05 (5percent of starting material), 2.18 (3H, s), 4.30 (2H, s) and 4.35 (5percent of dibromo compound) ppm downfield from tetramethylsilane. The infrared spectrum showed an absorption at 5.49 microns., 37830-90-3

Chemical properties determine the actual use. Each compound has specific chemical properties and uses. We look forward to more synthetic routes in the future to expand 4,5-Dimethyl-1,3-dioxol-2-one reaction routes.

Reference£º
Patent; Pfizer Inc.; US4448732; (1984); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”80841-78-7

To BIC (110 g, 1 eq) was added acetone (385 mL, 3.5 vol) at 25C – 30C, and the mixture was dissolved by stirring for 5 min. Sodium carbonate (20.85 g, 1.3 eq) and potassium iodide (0.25 g, 0.01) were added, and the mixture was stirred for 10 min. A solution of 4-chloromethyl-5-methyl-2-oxo-1,3-dioxolene (31.456 g, 1.4 eq) in acetone (165 mL, 1.5 vol) was added thereto. The reaction mixture was heated to 45C – 50C, and stirred at the same temperature for 12 hr. Using TLC (thin layer chromatography) (TLC eluent: 10% methanol/methylene chloride, detection method: UV), complete disappearance of BIC was confirmed. The reaction mixture was cooled to 25C – 30C. Then, the solvent contained in the reaction mixture was evaporated under reduced pressure at 40C – 45C. To the obtained residue were added 10% brine (550 mL, 5 vol) and toluene (550 mL, 5 vol). Furthermore, the mixture was adjusted to pH 7 – 8 by adding 5% hydrochloric acid (33 mL), stirred for 10 min, left standing for 5 min and partitioned. The aqueous layer was extracted with toluene (2×330 mL, 2×3 vol). The extracts were combined with the organic layer, 10% brine (550 mL, 5 vol) was added, and the mixture was stirred for 5 min, left standing for 45 min, partitioned, and concentrated under reduced pressure at 40C – 45C to give TOLM (110 g, 90%). [0306] To the obtained TOLM was added acetone (110 mL, 1 vol), and the mixture was stirred at 25C – 30C for 30 min. n-Heptane (440 mL, 4 vol) was added, and the mixture was cooled to 5C – 10C and stirred at 5C – 10C for 30 min, whereby precipitation of a solid was confirmed. The solid (80 g, 66%) was collected by filtration, and blast dried. To the obtained solid was added isopropyl alcohol (400 mL, 5 vol), and the mixture was heated to 50C – 55C and stirred at 50C – 55C for 1 hr. Then, the mixture was cooled to 25C – 30C, and stirred at 25C – 30C for 1 hr. The resulting solid was filtered and suction-filtered for 10 min to give TOLM (76 g, 62%).

The chemical industry reduces the impact on the environment during synthesis, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; API Corporation; SEKI, Masahiko; EP2891650; (2015); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact.37830-90-3, 4,5-Dimethyl-1,3-dioxol-2-one it is a common compound, a new synthetic route is introduced below.37830-90-3

Example 17 Preparation of 5-methyl-4-hydroxymethyl-2-oxo-1,3-dioxolene A solution of 4,5-dimethyl-2-oxo-1,3-dioxolene (1 mmol) and selenium dioxide (2.5 mmol) in dioxane was heated at reflux for 1 h. Evaporation, extraction and chromatography gave 5-methyl-4-hydroxymethyl-2-oxo-1,3-dioxolene as a yellow oil. TLC: Rf=0.5, 5percent MeOH-dichloromethane.

Chemical properties determine the actual use. Each compound has specific chemical properties and uses. We look forward to more synthetic routes in the future to expand 4,5-Dimethyl-1,3-dioxol-2-one reaction routes.

Reference£º
Patent; Metabasis Therapeutics, Inc.; US6284748; (2001); B1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact.37830-90-3, 4,5-Dimethyl-1,3-dioxol-2-one it is a common compound, a new synthetic route is introduced below.37830-90-3

To a solution of 16 grams 4,5-dimethyl-1, 3-dioxol-2-one in CC14 (250 mE) was added N135 (23.4 g,131.5 mmol) and AII3N (1.3 g, 7.88 mmol), then the reaction mixture was heated to 80¡ã C. and stirred for 2 hrs. Monitored the starting material gone by TLC. The mixture was filtered and the filtrate was washed with water and brine, the organic phase was dried over Na2504 and concentrated to give crude product as a yellow oil which was used directly next step (25.3 g, yield 93percent).

Chemical properties determine the actual use. Each compound has specific chemical properties and uses. We look forward to more synthetic routes in the future to expand 4,5-Dimethyl-1,3-dioxol-2-one reaction routes.

Reference£º
Patent; KULING THERAPEUTICS; DING, Qiang; Wang, Xiaohu; (55 pag.)US2017/298090; (2017); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem