Tag: M.W:100-200

The molecularity is the number of molecules that collide during that step in the mechanism. If only a single reactant molecule in an elementary reaction, that step is designated as unimolecular; if there are two reactant molecules, it is bimolecular.80841-78-7. A new synthetic method of this compound is introduced below., 80841-78-7

Example 96.20 g of (III) were suspended in a mixture of 15.5 ml of tetrahydrofuran:dimethyl sulfoxide (2:3, v/v). The mixture was cooled to 17C in order to add 0.45 g (1.3 equivalents) of sodium hydroxide. The mixture was then heated to 60C. After two hours 1 .55 g (1 .1 equivalents) of potassium carbonate were added to the mixture. The mixture was heated to 70C and 1 .41 g of (IV) dissolved in 16.2 ml of tetrahydrofuran were added to the mixture over 1 .5 hours. The reaction was completed in one hour. The mixture was cooled to room temperature. The mixture was then washed three times with a 29% solution of sodium chloride in water. Finally, the organic solvent was distilled and 18.6 ml of ethyl acetate were added. Finally (V) was crystallised from ethyl acetate by cooling. The mixture was cooled to 0-5C, it was filtered, washed with ethyl acetate and heptane and the resulting solid was dried in a heat cabinet. 5.54 g of (V) were obtained (80% yield). The resulting solid was analysed by HPLC, showing a purity of more than 97%.

A chemical reaction often occurs in steps, although it may not always be obvious to an observer.

Reference£º
Patent; INTERQUIM, S.A.; JOVE MARTI, Iban; MARQUILLAS OLONDRIZ, Francisco; WO2012/55994; (2012); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

Rate laws may be derived directly from the chemical equations for elementary reactions. This is not the case, however, for ordinary chemical reactions.37830-90-3, molecula formula is 4,5-Dimethyl-1,3-dioxol-2-one, below Introduce a new synthetic route., 37830-90-3

Example 1The feeding substance than the molar amount of the: DMDO: sulfonyl chloride to 1 : 1.3. The organic solvent is dichloromethane, the quality of the organic solvent with DMDO volume ratio is 1:7. Solid free radical scavenging agent is methyl hydroquinone, DMDO the quality of the amount of 1percent.To is provided with a magnetic stirring, constant pressure dropping funnel, reflux condensation tube, thermometer and is provided with a tail gas absorption device 500 ml flask to three in 350 ml dichloromethane, 50gDMDO, under stirring backflow state, slowly dropping 77g sulfonyl chloride, dropping time is approximately 2.5h, heat preservation after dropping 2h, rotary evaporation to remove the solvent. Furthermore, added to the bottoms of 0.5g methyl hydroquinone, for 90 ¡ãC conditions, stirring rearrangement 5h, obtaining a reaction crude. Analysis of the purity of crude 92.33percent, the crude in 2mmHg the vacuum degree of the vacuum distillation, to obtain the target product 52.8g, to yield 81.1percent, purity of 97.87percent.

Elementary reactions that involve the simultaneous collision of more than three molecules are highly improbable and have never been observed experimentally.

Reference£º
Patent; Six Anke Rui Da New Materials Co.,Ltd.; Bao, Yuanzhi; Weng, Shibing; Zhao, Zhongyao; (6 pag.)CN105348249; (2016); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

An elementary termolecular reaction involves the simultaneous collision of three atoms, molecules, or ions.4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, cas is 80841-78-7. Here is a downstream synthesis route of the compound 80841-78-7, 80841-78-7

Example 4; The reaction was carried out in the same manner as in Example 1 except that 4- (1-hydroxy-1-methylethyl) -2-propyl-1- {4- [2- (trityltetrazol-5-yl) phenyl] -carboxylic acid sodium salt (Chemical Formula 5) and 50 mL of N, N-dimethylacetamide were added, the temperature was adjusted to 5 to 10 DEG C and 4 g of potassium carbonate was added. A solution of 6.2 g of 4- (chloromethyl) -5-methyl-1,3-dioxol-2-one (Formula 6) in 6 mL of N, N-dimethylacetamide was added dropwise to the reaction portion, For 4 hours. After the reaction was completed, the reaction solution was cooled to 20 to 25 C, and then 220 mL of ethyl acetate, 30 g of salt, and 170 mL of purified water were sequentially added to the reaction mixture, followed by separation of the organic layer, followed by the addition of 30 g of salt and 170 mL of purified water . & Lt; / RTI & gt; 1 g of activated carbon and 20 g of anhydrous sodium sulfate were added to the organic layer, followed by stirring for 30 minutes to 1 hour, followed by filtration. The filtrate was concentrated under reduced pressure, and 100 mL of acetonitrile was added to the residue, followed by stirring at 50 to 55 DEG C for 1 hour. The crystals were cooled to 0 to 5 C., stirred for 2 hours, filtered, washed with 50 mL of isopropyl alcohol and dried to obtain 21.7 g (yield: 93%, purity: 99.96%) of tritylolemethanemethoxysilane

There are, however, a few established termolecular elementary reactions. The reaction of nitric oxide with oxygen appears to involve termolecular steps.

Reference£º
Patent; DONGBANG FTL CO., LTD; Song, Tae Hong; Jung, Hun Suk; Jang, Do Yeon; Moon, Chung Sun; Jung, Hee Jung; (18 pag.)KR101526249; (2015); B1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

37830-90-3, A balanced equation for a chemical reaction indicates what is reacting and what is produced, but it reveals nothing about how the reaction actually takes place. The reaction mechanism is the process, or pathway, by which a reaction occurs.37830-90-3. An updated downstream synthesis route of 37830-90-3 as follows.

37830-90-3, To a solution of 4,5-dimethyl-1,3-dioxolene-2-one (TCI, 10 g, 88 mmol) and N- bromosuccinimide (Fluka, 15.69 g, 88 mmol) in carbon tetrachloride (250 mL) was added benzoyl peroxide (Acros, 500 mg, 2.1 mmol). The reaction mixture was then refluxed for 2.5 h after which time the volatiles were evaporated under vacuum. The resulting residue was triturated with some carbon tetrachloride, filtered and the solid cake was washed with carbon tetrachloride. The filtrate volatiles were removed under vacuum and the yellow oily residue was distilled under vacuum (2-5 torr) to give 4-bromomethyl-5-methyl-1,3-dioxolene-2-one 903 (8.35 g, b.p. 94-98 ¡ãC, 49percent) as a pale yellow oil. 1H NMR (CDCI3) 8 4.21 (s, 2H), 2.17 (s, 3H).

A chemical reaction often occurs in steps, although it may not always be obvious to an observer.

Reference£º
Patent; RIGEL PHARMACEUTICALS, INC.; WO2005/97760; (2005); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

Rate laws may be derived directly from the chemical equations for elementary reactions. This is not the case, however, for ordinary chemical reactions.80841-78-7, molecula formula is 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, below Introduce a new synthetic route., 80841-78-7

Example 5; Preparation of trityl olmesartan medoxomilTo dimethyl sulphoxide (800 ml), sodium hydroxide powder (50 gms) was added under nitrogen atmosphere and stirred at 20-250C for 10 minutes. To this, 4-( 1 -hydroxy- 1- methylethyl)-2-propyl-imidazole-5-ethyl carboxylate (100 gms) was added at 20-250C. 5- (4′-bromomethyl-biphenyl)-2-yl-1 -trityl tetrazole (270 gms) was added slowly at 20-250C, and the reaction mass was stirred at 20-250C for 12 hours. Further 10% sodium hydroxide solution (100 ml) was added to the reaction mass at 20-250C. The temperature of the reaction mass was raised to 40-450C, the contents stirred at 40-450C for 2 hours and 5- methyl-2-oxo-1 ,3-dioxane-4-yl)methyl chloride (160 gms) was added slowly at 45-5O0C over a period of 45 minutes. The contents were stirred at 45-5O0C for 2 hours. The reaction mass was then cooled to 0-50C, stirred for 1 hour at 0-50C, filtered and slurried in water (1.0 It) at 40-450C for 1 hour, filtered at 4O0C and dried at 4O0C. To the dried material, ethyl acetate (2.5 It) was added, heated to 50-550C for complete dissolution, ethyl acetate was distilled off to 1.0 It stage under vacuum at 45-5O0C. The contents were cooled to 0-50C, stirred at 0-50C for 3 hours, filtered, washed with chilled methanol (100 ml) and dried under vacuum at 40-450C to give 250 gms of the title compound. Purity by HPLC : > 99%

Chemical properties determine the actual use. Each compound has specific chemical properties and uses. We look forward to more synthetic routes in the future to expand 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one reaction routes.

Reference£º
Patent; CIPLA LIMITED; CURTIS, Philip, Anthony; WO2008/43996; (2008); A2;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

An elementary termolecular reaction involves the simultaneous collision of three atoms, molecules, or ions.4,5-Dimethyl-1,3-dioxol-2-one, cas is 37830-90-3. Here is a downstream synthesis route of the compound 37830-90-3, 37830-90-3

A mixture of 4,5-dimethyl-1,3-dioxol-2-one (1.0 g, 8.8 mmol), benzoylperoxide (60 mg, 0.25 mmol) and N-bromosuccinimide (1.6 g, 9.0 mmol) in carbon tetrachloride (10 mL) was heated at reflux for 2 h. The solid was removed from the reaction mixture by filtration. The mother liquid was washed with sat. NaHCO3 and brine, dried over MgSO4 and concentrated. The crude product, 4-(bromomethyl)-5-methyl-1,3-dioxol-2-one, was obtained as a yellow oil (1.7 g) and was used without further purification in the next step.

A chemical reaction often occurs in steps, although it may not always be obvious to an observer.

Reference£º
Patent; Martinsson, Jessica; Faernegardh, Katarina; Joensson, Mattias; Ringom, Rune; US2015/25068; (2015); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

An elementary termolecular reaction involves the simultaneous collision of three atoms, molecules, or ions.4,5-Dimethyl-1,3-dioxol-2-one, cas is 37830-90-3. Here is a downstream synthesis route of the compound 37830-90-3, 37830-90-3

[01658] A solution of 4,5-dimethyl-2-oxo-1,3-dioxolene (1 mmole) and selenium dioxide (2.5 mmole) in dioxane was heated at reflux for 1 h. Evaporation, extraction and chromatography gave 5-methyl-4-hydroxymethyl-2-oxo-1,3-dioxolene as a yellow oil. TLC: RPf=0.5, 5percent MeOH-dichloromethane. [01659] A solution of 5-methyl-4-hydroxymethyl-2-oxo-1,3-dioxolene (1 mmole) in DMF was treated with tert-butyldimethylsilane (1.2 mmole) and imidazole (2.2 mmole) at 25 C. for 24 h. Extraction and chromatography gave 5-methyl-4-tert-butyldimethylsilyloxymethyl-2-oxo-1,3-dioxolene. [01660] A solution of 5-methyl-4-tert-butyldimethylsilyloxymethyl-2-oxo-1,3-dioxolene (1 mmole) and Lawesson’s reagent (1.2 mmole) in toluene was heated to 120 C. for 12 h. Extraction and chromatography gave 5-methyl-4-tert-butyldimethylsilyloxymethyl-2-thio-1,3-dioxolene. [01661] A solution of 5-methyl-4-tert-butyldimethylsilyloxymethyl-2-thio-1,3-dioxolene in methanolic hydrogen chloride was stirred at 0 C. for 1 h and 25 C. for 12 h. Extraction and chromatography gave 5-methyl-4-hydroxymethyl-2-thio-1,3-dioxolene.

Elementary reactions that involve the simultaneous collision of more than three molecules are highly improbable and have never been observed experimentally.

Reference£º
Patent; Metabasis Therapeutics, Inc.; US6756360; (2004); B1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

80841-78-7, The molecularity is the number of molecules that collide during that step in the mechanism. If only a single reactant molecule in an elementary reaction, that step is designated as unimolecular; if there are two reactant molecules, it is bimolecular.80841-78-7. A new synthetic method of this compound is introduced below.

1L glass reaction flask was added with 600ml of acetone, 114.8g of intermediate 1 was added with stirring, then 12.8g of sodium hydroxide was added, the temperature was raised to 50-60 C, and the reaction was incubated for 5 hours, and the reaction was monitored by HPLC. To 20-30 C, add 2.8g potassium iodide, 36.0g 4-chloromethyl-5-methyl-1,3-dioxol-2-one, and increase the temperature to 50-60 C after the addition After 1 hour of heat preservation reaction, the temperature was lowered to 20-30 C, filtered, and the filter cake was rinsed with 115 ml of acetone, and the filtrate was combined. The filtrate was concentrated under reduced pressure at 40-50 C until no obvious solvent flowed out, and 320 ml of acetonitrile was added to cool down. The mixture was decanted to 20-30 C for 1 hour, filtered, and the filter cake was rinsed with 320 ml of acetonitrile. The filter cake was blast dried at 40-50 C for 12 hours to obtain a white solid 110.0 g (intermediate 2). The rate was 85.8%, HPLC: 99.2%.

This molecular description is the mechanism of the reaction; it describes how individual atoms, ions, or molecules interact to form particular products. The stepwise changes are collectively called the reaction mechanism.

Reference£º
Patent; Jiashi (Hunan) Pharmaceutical Technology Co., Ltd.; Dai Yongzhi; Liu Hu; Zhu Laifa; Cai Jian; (8 pag.)CN108341804; (2018); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

We know that the rate of many reactions can be accelerated by catalysts. A catalyst speeds up the rate of a reaction by lowering the activation energy; in addition, the catalyst is regenerated in the process. 80841-78-7, molecula formula is C5H5ClO3, below Introduce a new synthetic route., 80841-78-7

Example 1-5 (0330) (0331) A mixture of BIC (0.6 g, 0.83 mmol), potassium iodide (0.069 g, 0.41 mmol), OXC (0.245 g, 1.65 mmol) and methyl ethyl ketone (9.0 mL, 15 vol) was stirred at 50 C. for 20 hr. The reaction mixture was filtered, the filtrate was concentrated under reduced pressure, and the obtained concentrated residue was purified by silica gel column chromatography (20-22% ethyl acetate/hexane) to give TOLM (650 mg, yield 84.4%). (0332) Mass: 801 [M+H]+, 824 [M+Na]+.

This molecular description is the mechanism of the reaction; it describes how individual atoms, ions, or molecules interact to form particular products. The stepwise changes are collectively called the reaction mechanism.

Reference£º
Patent; API CORPORATION; Seki, Masahiko; US2015/239854; (2015); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

An elementary termolecular reaction involves the simultaneous collision of three atoms, molecules, or ions.4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, cas is 80841-78-7. Here is a downstream synthesis route of the compound 80841-78-7, 80841-78-7

Example 236.0 g (50.3 mmol) ethyl 4-(1-hydroxy-1-methylethyl)-2-propyl-1-{4-[2-(trityltetrazol-5-yl)-phenyl]phenyl}-methyl imidazole-5-carboxylate (Va) and 3.0 g (75.4 mmol) of NaOH were suspended in 413 ml dimethylacetamide. The suspension was then stirred at room temperature for 20 h and after that 6.9 g (50.3 mmol) of K2CO3, were added. The mixture was cooled to 0 C. and solution of 15.4 g (70.4 mmol) 4-chloromethyl-5-methyl-2-oxo-1,3-dioxolene in 39 ml of dimethylacetamide were slowly added. The mixture was slowly heated to 50 C. and stirred at this temperature for 2 h. After esterification was completed, the mixture was cooled to 10 C. and poured into a mixture of 625 ml of ethyl acetate and 625 ml of 10% NaCl, and stirred at 25 C. for 15 min. The phases were separated and organic phase was washed 2¡Á with 500 ml of 10% NaCl, dried over Na2SO4 and filtered. The filtrate was concentrated up to ? (approximately 270 g) at reduced pressure.To the resulting solution, 80 ml of ethanol and 8.3 ml (100 mmol) of conc. HCl were added and stirred at 24-26 C. for 3 h. To the cooled mixture 600 ml of water was added and pH of the suspension was estimated to 5 by addition of 5 M NaOH. The phases were stirred for 15 min and separated. Water phase was reextracted with 150 ml of ethyl acetate. Collected organic phases were dried over Na2SO4, filtered and concentrated under reduced pressure. 560 ml of ethyl acetate were added and the mixture was evaporated again. After that, 300 ml of ethyl acetate were added and the mixture was cooled to 20 C. and stirred for 1 h, filtered off and washed with 20 ml of fresh ethyl acetate. The yield of the product (I) was 21 g (75%).

The chemical industry reduces the impact on the environment during synthesis, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; KRKA; US2009/131680; (2009); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem