Tag: 80841-78-7

80841-78-7, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one is a Dioxole compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

Example 236.0 g (50.3 mmol) ethyl 4-(1-hydroxy-1-methylethyl)-2-propyl-1-{4-[2-(trityltetrazol-5-yl)-phenyl]phenyl}-methyl imidazole-5-carboxylate (Va) and 3.0 g (75.4 mmol) of NaOH were suspended in 413 ml dimethylacetamide. The suspension was then stirred at room temperature for 20 h and after that 6.9 g (50.3 mmol) of K2CO3, were added. The mixture was cooled to 0 C. and solution of 15.4 g (70.4 mmol) 4-chloromethyl-5-methyl-2-oxo-1,3-dioxolene in 39 ml of dimethylacetamide were slowly added. The mixture was slowly heated to 50 C. and stirred at this temperature for 2 h. After esterification was completed, the mixture was cooled to 10 C. and poured into a mixture of 625 ml of ethyl acetate and 625 ml of 10% NaCl, and stirred at 25 C. for 15 min. The phases were separated and organic phase was washed 2¡Á with 500 ml of 10% NaCl, dried over Na2SO4 and filtered. The filtrate was concentrated up to ? (approximately 270 g) at reduced pressure.To the resulting solution, 80 ml of ethanol and 8.3 ml (100 mmol) of conc. HCl were added and stirred at 24-26 C. for 3 h. To the cooled mixture 600 ml of water was added and pH of the suspension was estimated to 5 by addition of 5 M NaOH. The phases were stirred for 15 min and separated. Water phase was reextracted with 150 ml of ethyl acetate. Collected organic phases were dried over Na2SO4, filtered and concentrated under reduced pressure. 560 ml of ethyl acetate were added and the mixture was evaporated again. After that, 300 ml of ethyl acetate were added and the mixture was cooled to 20 C. and stirred for 1 h, filtered off and washed with 20 ml of fresh ethyl acetate. The yield of the product (I) was 21 g (75%).

The synthetic route of 80841-78-7 has been constantly updated, and we look forward to future research findings.

Reference£º
Patent; KRKA; US2009/131680; (2009); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

80841-78-7, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one is a Dioxole compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

Example 3; Preparation of olmesartan medoxomilTo dimethyl acetamide (800 ml) was added 4-(1-hydroxy-1-methylethyl)-2-propyl imidazol- 5-carboxylic acid ethyl ester (100 gms) and powdered potassium carbonate (200 gms). To this was charged 4-[2-(trityltetrazol-5-yl)phenyl]benzyl bromide (300 gms) at 45-50C. The contents were stirred for 8-10 hours at 45-50C. The insolubles were filtered. The contents were cooled to 5-100C. Potassium tertiary butoxide (100 gms) was charged at a temperature below 45C. The reaction was maintained at 40-450C for 3 hrs. To this was slowly added 5-methyl-2-oxo-1 ,3-dioxane-4-yl) methyl chloride at 40-450C over a period of 1 hour. The contents were heated to 60-650C and maintained for 4 hours. The reaction mass was then cooled to 30-350C and was neutralized with concentrated hydrochloride acid. The reaction mass was filtered to remove inorganics. The reaction mass was charcoalized using charcoal (10 gms) and was stirred for 30 minutes at 40-450C. The reaction mass was filtered over hyflo. The clear filtrate was acidified with hydrochloric acid (100 ml) slowly at 25-30C. The contents were stirred at 60C for 1 hour. The reaction mass was chilled to 0-5C and was filtered to remove tritanol. The reaction mass was concentrated under reduced pressure. The residue was quenched with water (500 ml), neutralized with base and extracted in dichloromethane (500 ml).The clear dichloromethane extract was then concentrated under reduced pressure, stripped off with acetone. The residue thus obtained was isolated from the acetone (250 ml) to give 55 gms of the title compound. Chromatogrphic purity- > 99%

80841-78-7 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one 9855518, aDioxole compound, is more and more widely used in various.

Reference£º
Patent; CIPLA LIMITED; CURTIS, Philip, Anthony; WO2008/43996; (2008); A2;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

80841-78-7, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one is a Dioxole compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

188.0kg of tetrahydrofuran was added to a glass-lined reactor, 54.0kg 4- (1- hydroxy-1-methylethyl) -2-propyl-1- {4- [2- (trityl-tetrazol -5 – yl) phenyl] phenyl} methylimidazole-5-carboxylate, 92.0.0kg 4.0kg purified water and lithium hydroxide monohydrate.After complete addition, 20 stirred for 18 hours, once every 2 hours the reaction temperature recording, tracking and detection TLC starting material to substantially complete the reaction.After completion of the reaction, 240.0kg Ethyl acetate and sodium chloride solution (20.0 kg of sodium chloride was added to 180.0kg purified water, and dissolved with stirring), stirred for 10 minutes, allowed to stand for 20 minutes stratification.The organic phase was washed with sodium chloride solution (32.0 kg of sodium chloride was added to 288.0kg purified water, stirred and dissolved) Average washed twice, each wash was stirred for 10 minutes and allowed to stand for 20 minutes.The organic phase was collected, dried over anhydrous sodium sulfate and stirred for 4 hours.Filtered, and the filtrate was concentrated under reduced pressure to remove ethyl acetate (water bath temperature controlled at 45 ¡À 5 , the degree of vacuum at -0.1 ~ -0.06MPa), a solution 188.0kg N, N- dimethylformamide, is added 15.3kg anhydrous potassium carbonate, 2.7kg of potassium iodide was stirred at 20 ¡À 10 was slowly added 14.5kg 4- chloro-5-methyl-1,3-dioxol-2-one, addition was completed, heating, feed temperature control reaction was stirred for 2 hours at 40 ¡À 2 .After completion of the reaction, the material was cooled to 15 ¡À 5 rejection filter, and the filtrate was added to a solution of sodium chloride (338.0kg sodium chloride to 940.0kg purified water, and dissolved with stirring), the following -5 ~ 0 stirred for 4h, rejection was filtered, the filter cake was charged to an oven baking pan blast drying oven at a temperature of 40 ¡À 5 8 hours.To give 58.2kg of trityl olmesartan medoxomil, a yield of 96.5%.

The synthetic route of 80841-78-7 has been constantly updated, and we look forward to future research findings.

Reference£º
Patent; Lianyungang Runzhong Pharmaceutical Co., Ltd.; Zhong Zhaobo; Cheng Jinrong; He Shaojie; Tang Zhaocheng; (6 pag.)CN110396084; (2019); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

80841-78-7, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one is a Dioxole compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

Example 3; Trityl olmesartan medoxomil (III); A solution of potassium salt 4 in methyl ethyl ketone from the preceding experiment (ca. 20 g of the salt) was diluted with methyl ethyl ketone (290 ml), and, after adding potassium iodide (2 g) and 4-chloromethyl-5-methyl-l,3-dioxol-2-one (7 g), the mixture was stirred at 50 0C for 7.5 h. After the reaction was completed, the mixture was filtered, and the filtrate was washed with methyl ethyl ketone (3 x 50 ml). After concentrating to ca. 160 ml in vacuo, ethanol (250 ml) was added, and the reaction mixture was again concentrated to ca. 300 ml in vacuo.The concentrated product in ethanol was inoculated and stirred at 50 0C for 0.5 h, and after getting thicker, diluted with ethanol (50 ml) and cooled to 20 C. The precipitated product was sucked off, washed with ethanol (2 x 20 ml) and dried in a vacuum drier at 50 C. 14.4 g (86 %) of the product was obtained.

As the paragraph descriping shows that 80841-78-7 is playing an increasingly important role.

Reference£º
Patent; ZENTIVA, A.S.; WO2007/48361; (2007); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.80841-78-7,4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one,as a common compound, the synthetic route is as follows.

(3) the C43 H39 N6 NaO3 AMST – 4 and DMF added in a reaction kettle, lowering the temperature to 0 C, adding potassium carbonate, maintain 0 C dropwise C5 H5 ClO3 AMST – 5 dissolved in DMF solution, after the completion of the dropping 85 C reaction 4 hours, monitoring the reaction is finished adding water, sodium chloride and ethyl acetate stirring extraction, liquid, separating the upper organic phase, a mixed solution of water and sodium chloride washing, separating the organic phase at upper layer for sodium sulfate drying, filtering, 60 C concentrated to the reagent, in acetonitrile for 30 C beating 1 hour, cooling to 25 C, filtering, cake isopropyl alcohol leaching, 75 C drying to constant weight to obtain the product C48 H44 N6 O6 AMST – 6; the C43 H39 N6 NaO3 AMST – 4, DMF, potassium carbonate, C5 H5 ClO3 AMST – 5, ethyl acetate, acetonitrile, water, sodium chloride and sodium sulfate the mass ratio of the 192:560: 62:1500: 1000:1500: 300:50;

As the paragraph descriping shows that 80841-78-7 is playing an increasingly important role.

Reference£º
Patent; Jiangxi Yong Tong Technology Co., Ltd.; Liu Zhongchun; (10 pag.)CN107311989; (2017); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.80841-78-7,4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one,as a common compound, the synthetic route is as follows.

To the flask was added 2000 g of acetone, 160 g of ethyl 4- (1-hydroxy-1-methylethyl) -2-propylimidazole-5-carboxylate (II), 150 g of K2CO3, 460 g of 4- [2- (Trityltetrazol-5-yl) phenyl] benzyl bromide (III), 20g KI, the temperature was raised to reflux, the reaction was incubated for 34-38 hours under stirring.Then add 102g KOH, reflux reaction 6 ~ 8h. Cool to 10 ~ 20 , add 170g DMDO-Cl, incubated for 30 ~ 60min.Heating to reflux, the reaction 22 to 26 hours.After the reaction was added 40g of diatomaceous earth, stirring for 30 to 60 minutes, suction filtration, 200g acetone rinse cake. To the filtrate was added 800g of drinking water and 200g of refined hydrochloric acid, the reaction at room temperature for 2 to 4 hours, filtered to remove by-product triphenylcarbinol. Dropping 10% K2CO3 aqueous solution, adjusting feedstock pH to 4, cooling to 10 ~ 20 , stirring crystallization 2h, filtration, the filter cake with a mixture of pre-cooled 45g acetone and 230g of drinking water washing and drying, to obtain Olmesartan Medoxomil 309 g, total yield 83.1% (relative to ethyl-4- (1-hydroxy-1-methylethyl) -2-propylimidazole-5- carboxylate (II)), purity: 99.27% of the main peak, 0.08% of the olmesartan acid, 0.14% of the triphenylmethanol, and 0.13% of the largest unidentified one.

As the paragraph descriping shows that 80841-78-7 is playing an increasingly important role.

Reference£º
Patent; Zhejiang Huahai Zhicheng Pharmaceutical Co., Ltd.; Zhejiang Huahai Pharmaceutical Co., Ltd.; Jin Congyang; Wang Jiquan; Zhang Wenling; Wang Peng; (10 pag.)CN107311990; (2017); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.80841-78-7,4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one,as a common compound, the synthetic route is as follows.

Example 5: The reaction part was charged with ethyl 4- (1-hydroxy-1-methylethyl) -2-propyl-1- {4- [2- (trityltetrazol-5-yl) phenyl] 22 g of 5-carboxylate (Formula 4), 3.1 g of sodium hydroxide and 90 mL of ethanol were added and the mixture was stirred at 20 to 25 C for 4 to 5 hours. When the reaction was completed, the reaction solution was concentrated. To the residue were added 50 mL of ethyl acetate and 50 mL of purified water. The mixture was stirred for 1 hour and then layered. The separated organic layer was washed twice with an aqueous solution containing 30 g of salt and 170 mL of purified water. 1 g of activated carbon and 20 g of anhydrous sodium sulfate were added to the organic layer, followed by stirring for 30 minutes to 1 hour, followed by filtration Respectively. After the filtrate was concentrated under reduced pressure, 50 mL of N, N-dimethylacetamide was added to the residue, the temperature was adjusted to 5 to 10 DEG C 4 g of potassium carbonate was added and 6.2 g of 4- (chloromethyl) -5-methyl-1,3-dioxol-2-one (Formula 6) was dissolved in N, N-dimethylacetamide 6 ML was added dropwise, and the mixture was reacted at 45 to 50 C for 4 hours with stirring. When the reaction is completed, the reaction solution is cooled to 20 to 25 After cooling, 220 mL of ethyl acetate, 30 g of salt and 170 mL of purified water were added successively. The organic layer was separated And then washed once more with an aqueous solution containing 30 g of salt and 170 mL of purified water. The organic layer was washed with 1 g of activated carbon, 20 g of sodium was added and stirred for 30 minutes to 1 hour, followed by filtration. The filtrate was concentrated under reduced pressure, and then acetone 100 mL of i-tril was added, and the mixture was stirred at 50 to 55 C for 1 hour. The crystals were cooled to 0 to 5 [deg.] C and stirred for 2 hours. Followed by washing with 50 mL of isopropyl alcohol, followed by drying to obtain 21.6 g (yield: 88%) of tritylolemecanemethoxysilane (formula 1a) Purity 99.97%) was obtained

80841-78-7 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one 9855518, aDioxole compound, is more and more widely used in various.

Reference£º
Patent; DONGBANG FTL CO., LTD; Song, Tae Hong; Jung, Hun Suk; Jang, Do Yeon; Moon, Chung Sun; Jung, Hee Jung; (18 pag.)KR101526249; (2015); B1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.80841-78-7,4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one,as a common compound, the synthetic route is as follows.

Example 1(1) Tritylation and DMDO Esterification ReactionsAfter mixing 4-(1-hydroxy-1-methylethyl)-2-propyl-1-[[2′-[1H-tetrazol-5-yl]biphenyl-4-yl]methyl]imidazole-5-carboxylic acid (30 g), acetone (210 mL), 1,8-diazabicyclo[5,4,0]-7-undecene [DBU] (25.5 g) and triphenylmethyl chloride [TPC] (23.79 g), water (0.6 mL) was added and acetone (30 mL) was poured into the mixture, and the reaction mixture was stirred at 48 to 52 C. for 2 hours. Then, water (0.9 mL) was added and 4-chloromethyl-5-methyl-1,3-dioxol-2-one [DMDO-Cl] (18.5 g) was poured in, and the reaction mixture was stirred at 48 to 52 C. for 5 hours.(2) Obtaining Crude Crystals of Trityl Olmesartan Medoxomil (Acetone Solvate Crystals)After the reaction mixture was cooled to 20 C. to precipitate crystals, it was stirred at 15 to 25 C. for 40 minutes, and water (96 mL) was added dropwise over a period of 25 minutes, and then the reaction mixture was cooled to 0 to 5 C. and stirred for 30 minutes. The precipitated crystals were filtered out and washed with acetone-water (150 mL), and wet crude crystals of (5-methyl-2-oxo-1,3-dioxolen-4-yl)methyl 4-(1-hydroxy-1-methylethyl)-2-propyl-1-[[2′-[2-(triphenylmethyl)-2H-tetrazol-5-yl]biphenyl-4-yl]methyl]imidazole-5-carboxylate (57.83 g) were obtained. These were then dried in vacuo at 60 C. for approximately 15 hours, and the dry acetone solvate crystals (57.50 g) were obtained.

As the paragraph descriping shows that 80841-78-7 is playing an increasingly important role.

Reference£º
Patent; DAIICHI SANKYO COMPANY, LIMITED; US2012/59172; (2012); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.80841-78-7,4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one,as a common compound, the synthetic route is as follows.

Step B, go to the reaction solution of compound (II) obtained in Step A with stirring,Add 6.27kg of anhydrous potassium carbonate powder and2.01kg iodine, replace the air with nitrogen, the nitrogen pressure in the kettle is ?0.01Mpa,The temperature was controlled at 50 ¡À 2 , and 13.80 kg of compound (IV) was added dropwise at a constant pressure.Add within 40 to 60 minutes. After the incubation reaction for 1.25 hours,Reduce the reaction mixture to below 10 C, extract with conventional solvents in an extraction kettle, wash with water, and separate the layers.The organic phase was distilled under reduced pressure to recover the solvent, crystallized, centrifuged,Drying gave 55.03 kg of crude compound (I).Step C: Add 192.61 kg of ethyl acetate to the 500L refining kettle, start stirring,55.03 kg of the crude compound (I) obtained in step B is added, and the feeding port is closed,Keep the pressure ?0.01MPa after replacing air with nitrogen,The temperature was raised to 75 C and dissolved for 25 minutes until it was clear. The filtrate was filtered and the temperature was reduced to 2.5 C.Centrifuge, put the filter cake into the double cone dryer,Under reduced pressure, a small flow of nitrogen was passed in for replacement three times, and the drying temperature was controlled to 40-50 C.Vacuum degree ?-0.09MPa, after drying for 1 hour,Increase the drying temperature to 50 60 and continue drying for 3 hours.54.06kg compound (1) finished product,The HPLC content was 99.93%, and the residual content of the compound (III) was 0.05%.

As the paragraph descriping shows that 80841-78-7 is playing an increasingly important role.

Reference£º
Patent; Shandong Xinhua Pharmaceutical Co., Ltd.; Zhu Lianbo; Wu Hui; Dou Guohua; (6 pag.)CN110590758; (2019); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.80841-78-7,4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one,as a common compound, the synthetic route is as follows.

Example 2; 36.0 g (50.3 mmol) ethyl 4-(l -hydroxy- 1-methy lethyl)-2-propy 1-1- {4-[2-(trityltetrazol-5-y I)- phenyl]phenyl} -methyl imidazole-5-carboxylate (Va) and 3.0 g (75.4 mmol) of NaOH were suspended in 413 ml dimethylacetamide. The suspension was then stirred at room temperature for 20 h and after that 6.9 g (50.3 mmol) of K2CO3, were added. The mixture was cooled to 00C and solution of 15.4 g (70.4 mmol) 4-chloromethyl-5-methyl-2-oxo-l,3- dioxolene in 39 ml of dimethylacetamide were slowly added. The mixture was slowly heated to 500C and stirred at this temperature for 2 h. After esterification was completed, the mixture was cooled to 10 0C and poured into a mixture of 625 ml of ethyl acetate and 625 ml of 10 % NaCl, and stirred at 25 0C for 15 min. The phases were separated and organic phase was washed 2chi with 500 ml of 10 % NaCl, dried over Na2SO4 and filtered. The filtrate was concentrated up to 14 (approximately 270 g) at reduced pressure.To the resulting solution, 80 ml of ethanol and 8.3 ml (100 mmol) of cone. HCl were added EPO and stirred at 24-26C for 3h. To the cooled mixture 600 ml of water was added and pH of the suspension was estimated to 5 by addition of 5 M NaOH. The phases were stirred for 15 min and separated. Water phase was reextracted with 150 ml of ethyl acetate. Collected organic phases were dried over Na2SO4, filtered and concentrated under reduced pressure. 560 ml of ethyl acetate were added and the mixture was evaporated again. After that, 300 ml of ethyl acetate were added and the mixture was cooled to 20 0C and stirred for Ih, filtered off and washed with 20 ml of fresh ethyl acetate. The yield of the product (I) was 21 g (75 %).

80841-78-7 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one 9855518, aDioxole compound, is more and more widely used in various.

Reference£º
Patent; KRKA; WO2007/17135; (2007); A2;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem