Dioxole related

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.80841-78-7,4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one,as a common compound, the synthetic route is as follows.

Step B, go to the reaction solution of compound (II) obtained in Step A with stirring,Add 6.27kg of anhydrous potassium carbonate powder and2.01kg iodine, replace the air with nitrogen, the nitrogen pressure in the kettle is ?0.01Mpa,The temperature was controlled at 50 ¡À 2 , and 13.80 kg of compound (IV) was added dropwise at a constant pressure.Add within 40 to 60 minutes. After the incubation reaction for 1.25 hours,Reduce the reaction mixture to below 10 C, extract with conventional solvents in an extraction kettle, wash with water, and separate the layers.The organic phase was distilled under reduced pressure to recover the solvent, crystallized, centrifuged,Drying gave 55.03 kg of crude compound (I).Step C: Add 192.61 kg of ethyl acetate to the 500L refining kettle, start stirring,55.03 kg of the crude compound (I) obtained in step B is added, and the feeding port is closed,Keep the pressure ?0.01MPa after replacing air with nitrogen,The temperature was raised to 75 C and dissolved for 25 minutes until it was clear. The filtrate was filtered and the temperature was reduced to 2.5 C.Centrifuge, put the filter cake into the double cone dryer,Under reduced pressure, a small flow of nitrogen was passed in for replacement three times, and the drying temperature was controlled to 40-50 C.Vacuum degree ?-0.09MPa, after drying for 1 hour,Increase the drying temperature to 50 60 and continue drying for 3 hours.54.06kg compound (1) finished product,The HPLC content was 99.93%, and the residual content of the compound (III) was 0.05%.

As the paragraph descriping shows that 80841-78-7 is playing an increasingly important role.

Reference£º
Patent; Shandong Xinhua Pharmaceutical Co., Ltd.; Zhu Lianbo; Wu Hui; Dou Guohua; (6 pag.)CN110590758; (2019); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.37830-90-3,4,5-Dimethyl-1,3-dioxol-2-one,as a common compound, the synthetic route is as follows.

PREPARATION 2 Preparation of 4-bromomethyl-5-methyl-1,3-dioxole-2-one According to the method described in Liebigs. Ann. Chem., 1977, 27-32 4,5-dimethyl-1,3-dioxole-2-one (500 mg, 4.38 mmol) and N-bromosuccinimide (0.78 g, 4.38 mmol) were heated under reflux in dry carbon tetrachloride in the presence of alpha-alpha’-azobisisobutyronitrile (7.5 mg) for 20 minutes. The reaction mixture was concentrated under reduced pressure to half the volume, and the precipitated solid was filtered by suction. After removing the solvent from the filtrate, the residue was analyzed by gas chromatography. The obtained mixture (792 mg), contained 70percent of the desired title compound and used for the subsequent reactions.

As the paragraph descriping shows that 37830-90-3 is playing an increasingly important role.

Reference£º
Patent; Sawai Pharmaceutical Co., Ltd.; US5006548; (1991); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

37830-90-3, 4,5-Dimethyl-1,3-dioxol-2-one is a Dioxole compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

[01658] A solution of 4,5-dimethyl-2-oxo-1,3-dioxolene (1 mmole) and selenium dioxide (2.5 mmole) in dioxane was heated at reflux for 1 h. Evaporation, extraction and chromatography gave 5-methyl-4-hydroxymethyl-2-oxo-1,3-dioxolene as a yellow oil. TLC: RPf=0.5, 5percent MeOH-dichloromethane. [01659] A solution of 5-methyl-4-hydroxymethyl-2-oxo-1,3-dioxolene (1 mmole) in DMF was treated with tert-butyldimethylsilane (1.2 mmole) and imidazole (2.2 mmole) at 25 C. for 24 h. Extraction and chromatography gave 5-methyl-4-tert-butyldimethylsilyloxymethyl-2-oxo-1,3-dioxolene. [01660] A solution of 5-methyl-4-tert-butyldimethylsilyloxymethyl-2-oxo-1,3-dioxolene (1 mmole) and Lawesson’s reagent (1.2 mmole) in toluene was heated to 120 C. for 12 h. Extraction and chromatography gave 5-methyl-4-tert-butyldimethylsilyloxymethyl-2-thio-1,3-dioxolene. [01661] A solution of 5-methyl-4-tert-butyldimethylsilyloxymethyl-2-thio-1,3-dioxolene in methanolic hydrogen chloride was stirred at 0 C. for 1 h and 25 C. for 12 h. Extraction and chromatography gave 5-methyl-4-hydroxymethyl-2-thio-1,3-dioxolene.

As the paragraph descriping shows that 37830-90-3 is playing an increasingly important role.

Reference£º
Patent; Metabasis Therapeutics, Inc.; US6756360; (2004); B1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.144690-92-6,Triphenyl methyl olmesartan,as a common compound, the synthetic route is as follows.

One hundred ml of methanol was added to 10 g of (5-methyl-2-oxo-l,3-dioxol- 4-yl) methyl 4-(2-hydroxypropan-2-yl)-2-propyl-l-((2′-(l-trityl-lH-tetrazol-5-yl) biphenyl-4-yl) methyl)-lH-imidazole-5-carboxylate (Pharmacostech). Then to the reaction mixture was added 10 g of resin pre-treated with hydrochloric acid of pH 2-3 (TRILUE SCR-IO gel type), followed by refluxing for 6 hours. The solid components were filtered out from the reaction mixture and washed with 100 ml of methanol. The solid substance obtained by vacuum distillation of the filter-in solution was dissolved into a small quantity of acetone, and n-hexane was added to the acetone solution to obtain 6.58 g (yield rate: 94%) of the standard compound represent by Formula 9: 1H NMR (300 MHz, DMSO), delta 7.50-7.69 (m, 4H), 7.03 (d, 2H, J=8.0 Hz), 6.85 (d, 2H, >8.0 Hz), 5.41 (s, 2H), 5.22 (s, IH), 5.05 (s, 2H), 2.50 (s, 2H), 2.07 (s, 3H).

As the paragraph descriping shows that 144690-92-6 is playing an increasingly important role.

Reference£º
Patent; PHARMACOSTECH CO., LTD.; KIM, Jae Won; CHA, Young Gwan; RYU, Hyung Chul; KIM, Sun Joo; WO2010/67913; (2010); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.80841-78-7,4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one,as a common compound, the synthetic route is as follows.

Example 2; 36.0 g (50.3 mmol) ethyl 4-(l -hydroxy- 1-methy lethyl)-2-propy 1-1- {4-[2-(trityltetrazol-5-y I)- phenyl]phenyl} -methyl imidazole-5-carboxylate (Va) and 3.0 g (75.4 mmol) of NaOH were suspended in 413 ml dimethylacetamide. The suspension was then stirred at room temperature for 20 h and after that 6.9 g (50.3 mmol) of K2CO3, were added. The mixture was cooled to 00C and solution of 15.4 g (70.4 mmol) 4-chloromethyl-5-methyl-2-oxo-l,3- dioxolene in 39 ml of dimethylacetamide were slowly added. The mixture was slowly heated to 500C and stirred at this temperature for 2 h. After esterification was completed, the mixture was cooled to 10 0C and poured into a mixture of 625 ml of ethyl acetate and 625 ml of 10 % NaCl, and stirred at 25 0C for 15 min. The phases were separated and organic phase was washed 2chi with 500 ml of 10 % NaCl, dried over Na2SO4 and filtered. The filtrate was concentrated up to 14 (approximately 270 g) at reduced pressure.To the resulting solution, 80 ml of ethanol and 8.3 ml (100 mmol) of cone. HCl were added EPO and stirred at 24-26C for 3h. To the cooled mixture 600 ml of water was added and pH of the suspension was estimated to 5 by addition of 5 M NaOH. The phases were stirred for 15 min and separated. Water phase was reextracted with 150 ml of ethyl acetate. Collected organic phases were dried over Na2SO4, filtered and concentrated under reduced pressure. 560 ml of ethyl acetate were added and the mixture was evaporated again. After that, 300 ml of ethyl acetate were added and the mixture was cooled to 20 0C and stirred for Ih, filtered off and washed with 20 ml of fresh ethyl acetate. The yield of the product (I) was 21 g (75 %).

80841-78-7 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one 9855518, aDioxole compound, is more and more widely used in various.

Reference£º
Patent; KRKA; WO2007/17135; (2007); A2;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

37830-90-3, 4,5-Dimethyl-1,3-dioxol-2-one is a Dioxole compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

To a solution of 16 grams 4,5-dimethyl-1, 3-dioxol-2-one in CC14 (250 mE) was added N135 (23.4 g,131.5 mmol) and AII3N (1.3 g, 7.88 mmol), then the reaction mixture was heated to 80¡ã C. and stirred for 2 hrs. Monitored the starting material gone by TLC. The mixture was filtered and the filtrate was washed with water and brine, the organic phase was dried over Na2504 and concentrated to give crude product as a yellow oil which was used directly next step (25.3 g, yield 93percent).

37830-90-3 4,5-Dimethyl-1,3-dioxol-2-one 142210, aDioxole compound, is more and more widely used in various.

Reference£º
Patent; KULING THERAPEUTICS; DING, Qiang; Wang, Xiaohu; (55 pag.)US2017/298090; (2017); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

37830-90-3, 4,5-Dimethyl-1,3-dioxol-2-one is a Dioxole compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

PREPARATION 1 4-Bromomethyl-5-methyl-2-oxo-1,3-dioxole To a stirred solution of 3.0 g of 4,5-dimethyl-2-oxo-1,3-dioxole in 100 ml of carbon tetrachloride was added 4.63 g of N-bromosuccinimide. The resulting solution was heated under reflux and irradiated for 15 minutes. The reaction mixture was cooled to 0¡ã-5¡ã C., filtered and evaporated to give the title product. The NMR spectrum (CDCl3) showed absorptions at 2.05 (5percent of starting material), 2.18 (3H, s), 4.30 (2H, s) and 4.35 (5percent of dibromo compound) ppm downfield from tetramethylsilane. The infrared spectrum showed an absorption at 5.49 microns.

As the paragraph descriping shows that 37830-90-3 is playing an increasingly important role.

Reference£º
Patent; Pfizer Inc.; US4448732; (1984); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

37830-90-3, 4,5-Dimethyl-1,3-dioxol-2-one is a Dioxole compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

PREPARATION 18 4-Carbo-(5-methyl-2-oxo-1,3-dioxol-4-ylmethoxy)methylpiperazine hydrochloric acid salt Combine 4,5-dimethyl-1,3-dioxol-2-one (3.42 g, 30 mmol), N-bromosuccinimide (5.34 g, 30 mmol) and AIBN (500 mg, 3 mmol) in anhydrous carbon tetrachloride (100 mL). Heat at reflux. After 2 hours, cool and filter. Concentrate the filtrate to give 4-bromomethyl-5-methyl-1,3-dioxol-2-one (6.5 g, crude) as an oil, which can be used for the next step without further purification.

37830-90-3 4,5-Dimethyl-1,3-dioxol-2-one 142210, aDioxole compound, is more and more widely used in various.

Reference£º
Patent; Hoechst Marion Roussel, Inc.; US5977139; (1999); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6, Triphenyl methyl olmesartan is a Dioxole compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

Take 40g of compound 5, Add 80mL of methanol, 330 mL of ethyl acetate, Warmed to 45 , After 8 hours of reaction, Add 860mL water, Insoluble matter was removed by filtration, The filtrate was concentrated, In oily liquid, Acetonitrile, Stirred under a solid precipitation, filter, Washed with ethanol, 23.2 g of white solid was obtained, The yield was 83.1% The HPLC purity was 99.2%.

144690-92-6 Triphenyl methyl olmesartan 19036162, aDioxole compound, is more and more widely used in various.

Reference£º
Patent; Disha Pharmaceutical Group Co., Ltd.; Zhang Zhaoxing; Zhang Hongqiang; Qin Litai; Li Wei; Li Zongwen; Xia Haijian; (6 pag.)CN103012382; (2016); B;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6, Triphenyl methyl olmesartan is a Dioxole compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

A solution of MTT in an organic solvent and water (20%) was heated for 4-8 hrs at reflux. When the solvents were either acetonitrile (ACN), isopropyl alcohol (IPA) or t-butanol (t-BuOH), 1 volume of water was added, and the reaction was stirred until the amount of MTT was less than 2%. The mixture was evaporated to dryness. Ethyl acetate (EtOAc, 1 volume) was added to the residue and then evaporated again (twice). The resulting solid was dissolved in EtOAc (12 vol) and heated to reflux. The solution was cooled (2 C.) and stirred for 2 hrs. The product was filtered, washed (EtOAc, 1 vol), and dried on vacuum (45 C.). Table 1 shows the process details with different organic solvents: TABLE 1 Total solvent Time Solvent(s) Volume Temperature ( C.) (hrs) pH ACN:H2O 5:1 + 1 85 7 4.89-4.3 IPA:H2O 5:1 + 1 85 7 4.62-4.25t-BuOH:H2O 5:1 + 1 85 7 4.78-4.28n-propanol:H2O 5:1 reflux 2.5 4.3n-BuOH:H2O 5:1 110 2.5 4.412-BuOH:H2O 5:1 100 3 4.5iso-penthanol:H2O 5:1 100 3 5DMA:H2O 5:1 100 4 4.5DMF:H2O 5:1 100 4 4.5

As the paragraph descriping shows that 144690-92-6 is playing an increasingly important role.

Reference£º
Patent; Hedvati, Lilach; Pilarsky, Gideon; Shenkar-Garcia, Natalia; US2006/148870; (2006); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem