Category: 80841-78-7

Name is 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, as a common heterocyclic compound, it belongs to Dioxole compound, and cas is 80841-78-7, its synthesis route is as follows.,80841-78-7

The reaction flask was charged with 697.5 g of compound V obtained in the previous step,414 g of anhydrous potassium carbonate (3.00 mol)163.4 g of 4-chloromethyl-5-methyl-1,3-dioxol-2-one (Compound VI) (1.10 mol)And 2500 ml of acetonitrile were refluxed for 2 hours,After the reaction,filter,The filtrate was concentrated to dryness,The residue was stirred in 1500 ml of ethyl acetate and 500 ml of water for 15 minutes,Layered, organic layer and then washed with water,Dried over anhydrous sodium sulfate,filter,The filtrate was concentrated to dryness,To give the crude product of compound VII,Recrystallization from toluene and petroleum ether,To obtain pure product 683.2 grams; two-step yield:85.40% (calculated as compound II).

With the complex challenges of chemical substances, we look forward to future research findings about 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one

Reference£º
Patent; Hunan Ouya biological Co. Ltd.; Lin, kaizhao; (19 pag.)CN103304550; (2016); B;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, cas is 80841-78-7, it is a common heterocyclic compound, the Dioxole compound, its synthesis route is as follows.,80841-78-7

Example 96.20 g of (III) were suspended in a mixture of 15.5 ml of tetrahydrofuran:dimethyl sulfoxide (2:3, v/v). The mixture was cooled to 17C in order to add 0.45 g (1.3 equivalents) of sodium hydroxide. The mixture was then heated to 60C. After two hours 1 .55 g (1 .1 equivalents) of potassium carbonate were added to the mixture. The mixture was heated to 70C and 1 .41 g of (IV) dissolved in 16.2 ml of tetrahydrofuran were added to the mixture over 1 .5 hours. The reaction was completed in one hour. The mixture was cooled to room temperature. The mixture was then washed three times with a 29% solution of sodium chloride in water. Finally, the organic solvent was distilled and 18.6 ml of ethyl acetate were added. Finally (V) was crystallised from ethyl acetate by cooling. The mixture was cooled to 0-5C, it was filtered, washed with ethyl acetate and heptane and the resulting solid was dried in a heat cabinet. 5.54 g of (V) were obtained (80% yield). The resulting solid was analysed by HPLC, showing a purity of more than 97%.

With the rapid development of chemical substances, we look forward to future research findings about 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one

Reference£º
Patent; INTERQUIM, S.A.; JOVE MARTI, Iban; MARQUILLAS OLONDRIZ, Francisco; WO2012/55994; (2012); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.80841-78-7,4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one,as a common compound, the synthetic route is as follows.,80841-78-7

Example 1-5 (0330) (0331) A mixture of BIC (0.6 g, 0.83 mmol), potassium iodide (0.069 g, 0.41 mmol), OXC (0.245 g, 1.65 mmol) and methyl ethyl ketone (9.0 mL, 15 vol) was stirred at 50 C. for 20 hr. The reaction mixture was filtered, the filtrate was concentrated under reduced pressure, and the obtained concentrated residue was purified by silica gel column chromatography (20-22% ethyl acetate/hexane) to give TOLM (650 mg, yield 84.4%). (0332) Mass: 801 [M+H]+, 824 [M+Na]+.

The synthetic route of 80841-78-7 has been constantly updated, and we look forward to future research findings.

Reference£º
Patent; API CORPORATION; Seki, Masahiko; US2015/239854; (2015); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, cas is 80841-78-7, it is a common heterocyclic compound, the Dioxole compound, its synthesis route is as follows.,80841-78-7

1L glass reaction flask was added with 600ml of acetone, 114.8g of intermediate 1 was added with stirring, then 12.8g of sodium hydroxide was added, the temperature was raised to 50-60 C, and the reaction was incubated for 5 hours, and the reaction was monitored by HPLC. To 20-30 C, add 2.8g potassium iodide, 36.0g 4-chloromethyl-5-methyl-1,3-dioxol-2-one, and increase the temperature to 50-60 C after the addition After 1 hour of heat preservation reaction, the temperature was lowered to 20-30 C, filtered, and the filter cake was rinsed with 115 ml of acetone, and the filtrate was combined. The filtrate was concentrated under reduced pressure at 40-50 C until no obvious solvent flowed out, and 320 ml of acetonitrile was added to cool down. The mixture was decanted to 20-30 C for 1 hour, filtered, and the filter cake was rinsed with 320 ml of acetonitrile. The filter cake was blast dried at 40-50 C for 12 hours to obtain a white solid 110.0 g (intermediate 2). The rate was 85.8%, HPLC: 99.2%.

With the rapid development of chemical substances, we look forward to future research findings about 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one

Reference£º
Patent; Jiashi (Hunan) Pharmaceutical Technology Co., Ltd.; Dai Yongzhi; Liu Hu; Zhu Laifa; Cai Jian; (8 pag.)CN108341804; (2018); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, cas is 80841-78-7, it is a common heterocyclic compound, the Dioxole compound, its synthesis route is as follows.,80841-78-7

Example 5; Preparation of trityl olmesartan medoxomilTo dimethyl sulphoxide (800 ml), sodium hydroxide powder (50 gms) was added under nitrogen atmosphere and stirred at 20-250C for 10 minutes. To this, 4-( 1 -hydroxy- 1- methylethyl)-2-propyl-imidazole-5-ethyl carboxylate (100 gms) was added at 20-250C. 5- (4′-bromomethyl-biphenyl)-2-yl-1 -trityl tetrazole (270 gms) was added slowly at 20-250C, and the reaction mass was stirred at 20-250C for 12 hours. Further 10% sodium hydroxide solution (100 ml) was added to the reaction mass at 20-250C. The temperature of the reaction mass was raised to 40-450C, the contents stirred at 40-450C for 2 hours and 5- methyl-2-oxo-1 ,3-dioxane-4-yl)methyl chloride (160 gms) was added slowly at 45-5O0C over a period of 45 minutes. The contents were stirred at 45-5O0C for 2 hours. The reaction mass was then cooled to 0-50C, stirred for 1 hour at 0-50C, filtered and slurried in water (1.0 It) at 40-450C for 1 hour, filtered at 4O0C and dried at 4O0C. To the dried material, ethyl acetate (2.5 It) was added, heated to 50-550C for complete dissolution, ethyl acetate was distilled off to 1.0 It stage under vacuum at 45-5O0C. The contents were cooled to 0-50C, stirred at 0-50C for 3 hours, filtered, washed with chilled methanol (100 ml) and dried under vacuum at 40-450C to give 250 gms of the title compound. Purity by HPLC : > 99%

As the rapid development of chemical substances, we look forward to future research findings about 80841-78-7

Reference£º
Patent; CIPLA LIMITED; CURTIS, Philip, Anthony; WO2008/43996; (2008); A2;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, cas is 80841-78-7, it is a common heterocyclic compound, the Dioxole compound, its synthesis route is as follows.,80841-78-7

Example 2; 36.0 g (50.3 mmol) ethyl 4-(l -hydroxy- 1-methy lethyl)-2-propy 1-1- {4-[2-(trityltetrazol-5-y I)- phenyl]phenyl} -methyl imidazole-5-carboxylate (Va) and 3.0 g (75.4 mmol) of NaOH were suspended in 413 ml dimethylacetamide. The suspension was then stirred at room temperature for 20 h and after that 6.9 g (50.3 mmol) of K2CO3, were added. The mixture was cooled to 00C and solution of 15.4 g (70.4 mmol) 4-chloromethyl-5-methyl-2-oxo-l,3- dioxolene in 39 ml of dimethylacetamide were slowly added. The mixture was slowly heated to 500C and stirred at this temperature for 2 h. After esterification was completed, the mixture was cooled to 10 0C and poured into a mixture of 625 ml of ethyl acetate and 625 ml of 10 % NaCl, and stirred at 25 0C for 15 min. The phases were separated and organic phase was washed 2chi with 500 ml of 10 % NaCl, dried over Na2SO4 and filtered. The filtrate was concentrated up to 14 (approximately 270 g) at reduced pressure.To the resulting solution, 80 ml of ethanol and 8.3 ml (100 mmol) of cone. HCl were added EPO and stirred at 24-26C for 3h. To the cooled mixture 600 ml of water was added and pH of the suspension was estimated to 5 by addition of 5 M NaOH. The phases were stirred for 15 min and separated. Water phase was reextracted with 150 ml of ethyl acetate. Collected organic phases were dried over Na2SO4, filtered and concentrated under reduced pressure. 560 ml of ethyl acetate were added and the mixture was evaporated again. After that, 300 ml of ethyl acetate were added and the mixture was cooled to 20 0C and stirred for Ih, filtered off and washed with 20 ml of fresh ethyl acetate. The yield of the product (I) was 21 g (75 %).

As the rapid development of chemical substances, we look forward to future research findings about 80841-78-7

Reference£º
Patent; KRKA; WO2007/17135; (2007); A2;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, cas is 80841-78-7, it is a common heterocyclic compound, the Dioxole compound, its synthesis route is as follows.,80841-78-7

Toluene (180 L) is placed into a reactor and water (3.17 L) is added, followed by addition of ethyl-4-(1 -hydroxy-1 -methylethyl)-2-propylimidazole-5- carboxylate (18.0 Kg). The mass is stirred for about 10 minutes, heated to about 45C, and potassium carbonate (25.85 Kg) is added. The temperature of the mass is raised to about 65C and maintained for about 45 minutes. N-(triphenylmethyl)- 5-[4′-(bromomethyl)biphenyl-2-yl]tetrazole (48.9 Kg) and tetrabutylammonium bromide (4.82 Kg) are added at the same temperature and the mixture is stirred at 60-700C for 10 hours. Reaction completion is verified using thin layerchromatography (TLC). After the reaction is complete, the mass is washed with water (3*120 L) at about 500C. The mass is cooled to about 25C and toluene (468 L) and potassium tertiary-butoxide (12.6 Kg) is added, then the mass is maintained at the same temperature for about 1 hour. Water (0.85 L) is added and the mass is maintained at the same temperature for about 2 hours. Reaction completion is verified using TLC, then 5-methyl-2-oxo-(1 ,3-dioxolene-4-yl)methyl chloride (20 Kg), tetrabutylammonium bromide (4.82 Kg), and sodium carbonate (3.96 Kg) are added at 40-450C. The mass is stirred at about 55C for about 11 hours. After the reaction is complete, the mass is cooled to about 20C, water (540 L) is added and the pH is adjusted to about 6-7 by adding 10% aqueous HCI. The layers are separated. The aqueous layer is extracted with toluene (240 L). The organic layers are combined and washed with water (270 L). The solvent is distilled under reduced pressure. Acetone (189 L) is added to the residue and the mixture is heated to about 45C to produce a solution, then the solution is cooled to about 300C and maintained for about 20 minutes, followed by cooling to about 2C and maintaining for about 3 hours. The formed solid is filtered, washed with acetone (54 L), and dried for about 4 hours. The material obtained is re- crystallized from acetonitrile to yield 34.0 Kg of the title compound.

As the rapid development of chemical substances, we look forward to future research findings about 80841-78-7

Reference£º
Patent; DR. REDDY’S LABORATORIES LTD.; DR. REDDY’S LABORATORIES, INC.; KOLLA, Naveen Kumar; MANNE, Nagaraju; NAREDLA, Anitha; SHINDE, Sachin Gulabrao; WO2011/14611; (2011); A2;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.80841-78-7,4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one,as a common compound, the synthetic route is as follows.,80841-78-7

Step B, go to the reaction solution of compound (II) obtained in Step A with stirring,Add 6.27kg of anhydrous sodium carbonate powder and 2.01kg of iodine, replace the air with nitrogen,The nitrogen pressure in the kettle is ?0.01Mpa, the control temperature is 50 ¡À 2 ,15.05 kg of compound (IV) was added dropwise at a constant pressure, and the addition was completed within 40 to 60 minutes.After the reaction was held for 1 hour, the reaction mixture was reduced to below 10 C.Extract with conventional solvents in an extraction kettle, wash with water, and separate the layers.The organic phase was distilled under reduced pressure to recover the solvent, crystallized, centrifuged,After drying, 54.88 kg of the crude compound (I) was obtained.Step C: Add 192.08 kg of ethyl acetate to the 500L refining kettle, start stirring,Add 54.88 kg of crude compound (I) obtained in step B, close the feed port,Keep the pressure ?0.01MPa after replacing air with nitrogen,The temperature was raised to 75 C and dissolved for 25 minutes until it was clear. The filtrate was filtered and the temperature was reduced to 2.5 C.Centrifuge, put the filter cake into the double cone dryer,Under reduced pressure, a small flow of nitrogen was passed in for replacement three times, and the drying temperature was controlled to 40-50 C.Vacuum degree ?-0.09MPa, after drying for 1 hour,Increase the drying temperature to 50 60 and continue drying for 3 hours.After cooling down, 53.60 kg of compound (1) was obtained, and the HPLC content was 99.87%.Compound (III) had a residual content of 0.06%.

80841-78-7 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one 9855518, aDioxole compound, is more and more widely used in various.

Reference£º
Patent; Shandong Xinhua Pharmaceutical Co., Ltd.; Zhu Lianbo; Wu Hui; Dou Guohua; (6 pag.)CN110590758; (2019); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

80841-78-7, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one is a Dioxole compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated,80841-78-7

A solution containing about 46 g of compound 4 was taken, 3.5g sodium iodide was added, 280 mL N, N-dimethylformamide, 11.2g DMDO-Cl was slowly added dropwise, 30 Minute addition is completed. After dropping, Heated to 55 , Reaction for 7 hours, The reaction is completely over. filter, Remove insolubles, The filtrate was poured into 700mL of water, Extraction with ethyl acetate, The ethyl acetate layer was collected, dry, filter, The filtrate is concentrated. To the oily substance obtained after the concentration was added 200 mL of ethanol, Stirring, A white solid precipitation, Collect the solid, Washed with 50mL cyclohexane beating, 45.0 g of product was obtained, Two-step total yield of 80.6% The purity of the product was 98% by HPLC.

The synthetic route of 80841-78-7 has been constantly updated, and we look forward to future research findings.

Reference£º
Patent; Disha Pharmaceutical Group Co., Ltd.; Zhang Zhaoxing; Zhang Hongqiang; Qin Litai; Li Wei; Li Zongwen; Xia Haijian; (6 pag.)CN103012382; (2016); B;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, cas is 80841-78-7, it is a common heterocyclic compound, the Dioxole compound, its synthesis route is as follows.

Example 4; The reaction was carried out in the same manner as in Example 1 except that 4- (1-hydroxy-1-methylethyl) -2-propyl-1- {4- [2- (trityltetrazol-5-yl) phenyl] -carboxylic acid sodium salt (Chemical Formula 5) and 50 mL of N, N-dimethylacetamide were added, the temperature was adjusted to 5 to 10 DEG C and 4 g of potassium carbonate was added. A solution of 6.2 g of 4- (chloromethyl) -5-methyl-1,3-dioxol-2-one (Formula 6) in 6 mL of N, N-dimethylacetamide was added dropwise to the reaction portion, For 4 hours. After the reaction was completed, the reaction solution was cooled to 20 to 25 C, and then 220 mL of ethyl acetate, 30 g of salt, and 170 mL of purified water were sequentially added to the reaction mixture, followed by separation of the organic layer, followed by the addition of 30 g of salt and 170 mL of purified water . & Lt; / RTI & gt; 1 g of activated carbon and 20 g of anhydrous sodium sulfate were added to the organic layer, followed by stirring for 30 minutes to 1 hour, followed by filtration. The filtrate was concentrated under reduced pressure, and 100 mL of acetonitrile was added to the residue, followed by stirring at 50 to 55 DEG C for 1 hour. The crystals were cooled to 0 to 5 C., stirred for 2 hours, filtered, washed with 50 mL of isopropyl alcohol and dried to obtain 21.7 g (yield: 93%, purity: 99.96%) of tritylolemethanemethoxysilane

As the rapid development of chemical substances, we look forward to future research findings about 80841-78-7

Reference£º
Patent; DONGBANG FTL CO., LTD; Song, Tae Hong; Jung, Hun Suk; Jang, Do Yeon; Moon, Chung Sun; Jung, Hee Jung; (18 pag.)KR101526249; (2015); B1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem