Category: 80841-78-7

4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”80841-78-7

Example 96.20 g of (III) were suspended in a mixture of 15.5 ml of tetrahydrofuran:dimethyl sulfoxide (2:3, v/v). The mixture was cooled to 17C in order to add 0.45 g (1.3 equivalents) of sodium hydroxide. The mixture was then heated to 60C. After two hours 1 .55 g (1 .1 equivalents) of potassium carbonate were added to the mixture. The mixture was heated to 70C and 1 .41 g of (IV) dissolved in 16.2 ml of tetrahydrofuran were added to the mixture over 1 .5 hours. The reaction was completed in one hour. The mixture was cooled to room temperature. The mixture was then washed three times with a 29% solution of sodium chloride in water. Finally, the organic solvent was distilled and 18.6 ml of ethyl acetate were added. Finally (V) was crystallised from ethyl acetate by cooling. The mixture was cooled to 0-5C, it was filtered, washed with ethyl acetate and heptane and the resulting solid was dried in a heat cabinet. 5.54 g of (V) were obtained (80% yield). The resulting solid was analysed by HPLC, showing a purity of more than 97%.

The chemical industry reduces the impact on the environment during synthesis, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; INTERQUIM, S.A.; JOVE MARTI, Iban; MARQUILLAS OLONDRIZ, Francisco; WO2012/55994; (2012); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”80841-78-7

Step B, go to the reaction solution of compound (II) obtained in Step A with stirring,Add 6.27kg of anhydrous sodium carbonate powder and 2.01kg of iodine, replace the air with nitrogen,The nitrogen pressure in the kettle is ?0.01Mpa, the control temperature is 50 ¡À 2 ,15.05 kg of compound (IV) was added dropwise at a constant pressure, and the addition was completed within 40 to 60 minutes.After the reaction was held for 1 hour, the reaction mixture was reduced to below 10 C.Extract with conventional solvents in an extraction kettle, wash with water, and separate the layers.The organic phase was distilled under reduced pressure to recover the solvent, crystallized, centrifuged,After drying, 54.88 kg of the crude compound (I) was obtained.Step C: Add 192.08 kg of ethyl acetate to the 500L refining kettle, start stirring,Add 54.88 kg of crude compound (I) obtained in step B, close the feed port,Keep the pressure ?0.01MPa after replacing air with nitrogen,The temperature was raised to 75 C and dissolved for 25 minutes until it was clear. The filtrate was filtered and the temperature was reduced to 2.5 C.Centrifuge, put the filter cake into the double cone dryer,Under reduced pressure, a small flow of nitrogen was passed in for replacement three times, and the drying temperature was controlled to 40-50 C.Vacuum degree ?-0.09MPa, after drying for 1 hour,Increase the drying temperature to 50 60 and continue drying for 3 hours.After cooling down, 53.60 kg of compound (1) was obtained, and the HPLC content was 99.87%.Compound (III) had a residual content of 0.06%.

The chemical industry reduces the impact on the environment during synthesis, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; Shandong Xinhua Pharmaceutical Co., Ltd.; Zhu Lianbo; Wu Hui; Dou Guohua; (6 pag.)CN110590758; (2019); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”80841-78-7

The reaction flask was charged with 697.5 g of compound V obtained in the previous step,414 g of anhydrous potassium carbonate (3.00 mol)163.4 g of 4-chloromethyl-5-methyl-1,3-dioxol-2-one (Compound VI) (1.10 mol)And 2500 ml of acetonitrile were refluxed for 2 hours,After the reaction,filter,The filtrate was concentrated to dryness,The residue was stirred in 1500 ml of ethyl acetate and 500 ml of water for 15 minutes,Layered, organic layer and then washed with water,Dried over anhydrous sodium sulfate,filter,The filtrate was concentrated to dryness,To give the crude product of compound VII,Recrystallization from toluene and petroleum ether,To obtain pure product 683.2 grams; two-step yield:85.40% (calculated as compound II).

The chemical industry reduces the impact on the environment during synthesis, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; Hunan Ouya biological Co. Ltd.; Lin, kaizhao; (19 pag.)CN103304550; (2016); B;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact.80841-78-7, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one it is a common compound, a new synthetic route is introduced below.80841-78-7

Example 2; 36.0 g (50.3 mmol) ethyl 4-(1-hydroxy-1-methylethyl)-2-propyl-1-(4-[2-(trityltetrazol-5-yl)-phenyl]phenyl}-methyl imidazole-5-carboxylate (Va) and 3.0 g (75.4 mmol) of NaOH were suspended in 413 ml dimethylacetamide. The suspension was then stirred at room temperature for 20 h and after that 6.9 g (50.3 mmol) of K2CO3 were added. The mixture was cooled to 0C and solution of 15.4 g (70.4 mmol) 4-chloromethyl-5-methyl-2-oxo-1,3-dioxolene in 39 ml of dimethylacetamide were slowly added. The mixture was slowly heated to 50C and stirred at this temperature for 2 h. After esterification was completed, the mixture was cooled to 10 C and poured into a mixture of 625 ml of ethyl acetate and 625 ml of 10 % NaCl, and stirred at 25 C for 15 min. The phases were separated and organic phase was washed 2x with 500 ml of 10 % NaCl, dried over Na2SO4 and filtered. The filtrate was concentrated up to ? (approximately 270 g) at reduced pressure. To the resulting solution, 80 ml of ethanol and 8.3 ml (100 mmol) of conc. HCl were added and stirred at 24-26C for 3h. To the cooled mixture 600 ml of water was added and pH of the suspension was estimated to 5 by addition of 5 M NaOH. The phases were stirred for 15 min and separated. Water phase was reextracted with 150 ml of ethyl acetate. Collected organic phases were dried over Na2SO4, filtered and concentrated under reduced pressure. 560 ml of ethyl acetate were added and the mixture was evaporated again. After that, 300 ml of ethyl acetate were added and the mixture was cooled to 20 C and stirred for 1h, filtered off and washed with 20 ml of fresh ethyl acetate. The yield of the product (I) was 21 g (75 %).

Chemical properties determine the actual use. Each compound has specific chemical properties and uses. We look forward to more synthetic routes in the future to expand 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one reaction routes.

Reference£º
Patent; KRKA, tovarna zdravil, d.d., Novo mesto; EP1816131; (2007); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”80841-78-7

Example 4; The reaction was carried out in the same manner as in Example 1 except that 4- (1-hydroxy-1-methylethyl) -2-propyl-1- {4- [2- (trityltetrazol-5-yl) phenyl] -carboxylic acid sodium salt (Chemical Formula 5) and 50 mL of N, N-dimethylacetamide were added, the temperature was adjusted to 5 to 10 DEG C and 4 g of potassium carbonate was added. A solution of 6.2 g of 4- (chloromethyl) -5-methyl-1,3-dioxol-2-one (Formula 6) in 6 mL of N, N-dimethylacetamide was added dropwise to the reaction portion, For 4 hours. After the reaction was completed, the reaction solution was cooled to 20 to 25 C, and then 220 mL of ethyl acetate, 30 g of salt, and 170 mL of purified water were sequentially added to the reaction mixture, followed by separation of the organic layer, followed by the addition of 30 g of salt and 170 mL of purified water . & Lt; / RTI & gt; 1 g of activated carbon and 20 g of anhydrous sodium sulfate were added to the organic layer, followed by stirring for 30 minutes to 1 hour, followed by filtration. The filtrate was concentrated under reduced pressure, and 100 mL of acetonitrile was added to the residue, followed by stirring at 50 to 55 DEG C for 1 hour. The crystals were cooled to 0 to 5 C., stirred for 2 hours, filtered, washed with 50 mL of isopropyl alcohol and dried to obtain 21.7 g (yield: 93%, purity: 99.96%) of tritylolemethanemethoxysilane

The chemical industry reduces the impact on the environment during synthesis, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; DONGBANG FTL CO., LTD; Song, Tae Hong; Jung, Hun Suk; Jang, Do Yeon; Moon, Chung Sun; Jung, Hee Jung; (18 pag.)KR101526249; (2015); B1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”80841-78-7

123.2g of compound and 2.5g of potassium hydroxide solid were added to a 500ml four-necked flask.DMAC76g, heated to 50 C, stirred for about 6h,The TLC dot plate showed that the compound 1 point disappeared, that is, the end of the hydrolysis reaction was judged.Cool to 15 ¡À 5 C, add KBr 0.64g, add DMDO-C16.5g, DMAC 10g,After about 40 minutes, the temperature was raised to 25¡À5C for 2h, then the temperature was raised to 50C, the reaction was about 6h, and the temperature was lowered again to 20¡À5C for 5h. The reaction solution was added with 324g water and 208g of dichloromethane.Shake well and let the layers separate. The aqueous layer was extracted with 70 g of dichloromethane and combined with several layers.It was washed twice with 206 g of water, and the last aqueous layer was extracted with 100 g of dichloromethane.The organic layers were combined and dried under reduced pressure at 45 C.After adding 100g of the upper batch of crystallization, the mother liquid is heated and refluxed for 25¡À5 minutes, and then naturally cooled.Then crystallization at 0 C for 6 h,Drying by suction filtration to obtain 23.2 g of trityl olmesartan medoxomil white solid powder.The yield was 93.4%. HPLC analysis, purity 99.7%, acid miscellaneous <0.05%,The olefinic impurity is <0.1%, and the other unknown single impurities are <0.1%. The chemical industry reduces the impact on the environment during synthesis, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, , I believe this compound will play a more active role in future production and life. Reference£º
Patent; Zhejiang Huahai Pharmaceutical Co., Ltd.; Xiong Xueqiang; Li Guoxiang; Wang Jiquan; (6 pag.)CN103880825; (2019); B;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”80841-78-7

Example 3; Preparation of olmesartan medoxomilTo dimethyl acetamide (800 ml) was added 4-(1-hydroxy-1-methylethyl)-2-propyl imidazol- 5-carboxylic acid ethyl ester (100 gms) and powdered potassium carbonate (200 gms). To this was charged 4-[2-(trityltetrazol-5-yl)phenyl]benzyl bromide (300 gms) at 45-50C. The contents were stirred for 8-10 hours at 45-50C. The insolubles were filtered. The contents were cooled to 5-100C. Potassium tertiary butoxide (100 gms) was charged at a temperature below 45C. The reaction was maintained at 40-450C for 3 hrs. To this was slowly added 5-methyl-2-oxo-1 ,3-dioxane-4-yl) methyl chloride at 40-450C over a period of 1 hour. The contents were heated to 60-650C and maintained for 4 hours. The reaction mass was then cooled to 30-350C and was neutralized with concentrated hydrochloride acid. The reaction mass was filtered to remove inorganics. The reaction mass was charcoalized using charcoal (10 gms) and was stirred for 30 minutes at 40-450C. The reaction mass was filtered over hyflo. The clear filtrate was acidified with hydrochloric acid (100 ml) slowly at 25-30C. The contents were stirred at 60C for 1 hour. The reaction mass was chilled to 0-5C and was filtered to remove tritanol. The reaction mass was concentrated under reduced pressure. The residue was quenched with water (500 ml), neutralized with base and extracted in dichloromethane (500 ml).The clear dichloromethane extract was then concentrated under reduced pressure, stripped off with acetone. The residue thus obtained was isolated from the acetone (250 ml) to give 55 gms of the title compound. Chromatogrphic purity- > 99%

The chemical industry reduces the impact on the environment during synthesis, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; CIPLA LIMITED; CURTIS, Philip, Anthony; WO2008/43996; (2008); A2;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”80841-78-7

In 130 ml of N,N-dimethyl acetamide, 14.5 g (20 mmol) of potassium 4-(2-hydroxypropan-2-yl)-2-propyl-1-((2′-(1-trityl-1H-tetrazol-5-yl)biphenyl-4-yl)methyl)-1H-imidazole-5-carboxylate, 3.0 g (2.2 mmol) of potassium carbonate powder and 1.4 g (8.4 mmol) of potassium iodide were added. The mixture was cooled to 0 C and 5.0 g (33 mmol) of 4-(chloromethyl)-5-methyl-1,3-dioxol-2-one was added at 0 to 5C. After the addition, the reaction mixture was warmed to 40-45 C within one hour, then the mixture was stirred at this temperature for 2h. The sample of reaction mixture was analysed (HPLC; tritylolmesartan medoxomil, 97.44%, 4-(2-hydroxypropan-2-yl)-2-propyl-1-((2′-(1-trityl-1H-tetrazol-5-yl)biphenyl-4-yl)methyl)-1H-imidazole-5-carboxylate 0.06 %). The mixture was cooled to 10 to 20C and then 250 ml of ethyl acetate was added. The mixture was cooled again to 5-10 C and then 200 ml of 10% NaCl was added slowly. The temperature should not be higher than 25 C during the addition. The phases were mixed separated and organic phase was washed with 100 ml of 10% NaCl (2*) and dried over anhydrous sodium sulphate. After the filtration filtrate was evaporated under reduced pressure at temperature under 45C to oily residue. To the residue 30 ml of acetonitrile was added at temperature not more than 45C. The mixture was stirred at this temperature for 10 minutes then was cooled to 20 to 25C and stirred at this temperature for 0.5 h and after that 3h at 0 to 5C. The suspension was filtered, washed with cold acetonitrile and dried at 40 to 50C. Yield: 17.0 g (91%) HPLC: 99.64 % of the product, all other impurities under 0.1%. IR: 3408, 1818, 1805, 1741, 1681, 1529, 1148, 1002, 699

The chemical industry reduces the impact on the environment during synthesis, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; Krka Tovarna Zdravil, D.D., Novo Mesto; EP2334668; (2011); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”80841-78-7

130 ml of N,N-dimethylacetamide, 14.0 g (20 mmol) of ethyl 4-(2-hydroxypropan-2-yl)-2-propyl-1-((2′-(1-trityl-1H-tetrazol-5-yl)biphenyl-4-yl)methyl)-1H-imidazole-5-carboxylate and 2.2 g (16 mmol) of KOH were charged into reaction vessel at room temperature under inert atmosphere. The mixture was stirred at room temperature for 2 h, and then the sample of reaction mixture was analysed (HPLC; starting material 0.2 %, hydrolysed starting material 98.11 %). Then 3.0 g (2.2 mmol) of potassium carbonate powder and 1.4 g (8.4 mmol) of potassium iodide were added. The reaction mixture was cooled to 0 C and 5.0 g (33 mmol) of 4-(chloromethyl)-5-methyl-1,3-dioxol-2-one was added at 0 to 5C. After the addition, the reaction mixture was warmed to 40-45 C within one hour, then the mixture was stirred at this temperature for 2h. The sample of reaction mixture was analysed (HPLC; tritylolmesartan medoxomil 97.22 %, 4-(2-hydroxypropan-2-yl)-2-propyl-1-((2′-(1-trityl-1H-tetrazol-5-yl)biphenyl-4-yl)methyl)-1H-imidazole-5-carboxylate 0.09 %). The mixture was cooled to 10 to 20 C and then 250 ml of ethyl acetate was added. The mixture was cooled again to 5-10 C and then 200 ml of 10 % NaCl was added slowly. The temperature should not be higher than 25 C during the addition. The phases were mixed separated and organic phase was washed with 100 ml of 10 % NaCl (2*) and dried over anhydrous sodium sulphate. After the filtration filtrate was evaporated under reduced pressure at temperature under 45C to oily residue. To the residue 30 ml of acetonitrile was added at temperature not more than 45C. The mixture was stirred at this temperature for 10 minutes then was cooled to 20 to 25C and stirred at this temperature for 0.5 h and after that 3h at 0 to 5C. The suspension was filtered, the cake washed with cold acetonitrile and dried at 40 to 50C. Yield: 17.0 g (94%) HPLC: 99.72 % of the product, all impurities are under 0.1%. IR: 3408, 1818, 1805, 1741, 1681, 1529, 1147, 1003, 699 XRD:

The chemical industry reduces the impact on the environment during synthesis, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; Krka Tovarna Zdravil, D.D., Novo Mesto; EP2334668; (2011); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”80841-78-7

Example 1; Preparation of olmesartan medoxomilTo dimethyl acetamide (300 ml) was added 4-(1-hydroxy-1-methylethyl)-2-propyl imidazol- 5-carboxylic acid ethyl ester (50 gms) and powdered sodium hydroxide (26 gms). To this, 4-[2-(trityltetrazol-5-yl)phenyl]benzyl bromide (135 gms) was charged at 45-500C. The contents were stirred for 5 hours at 45-500C. Diisopropylethyl amine (100 ml) was charged to the reaction mass at 40-450C. A solution of 5-methyl-2-oxo-1 , 3-dioxane-4-yl)methyl chloride (80 gms) diluted with dimethyl acetamide (160 ml) was slowly added to the reaction mass at 40-450C over a period of 1 hour. The contents were heated to 60-650C and maintained for 4 hours. The reaction mass was then cooled to 30-350C and neutralized with concentrated hydrochloride acid. The reaction mass was filtered to remove inorganic impurities, charcoalized using charcoal (10 gms) andstirred for 30 minutes at 40-450C. The reaction mass was filtered over hyflo. The clear filtrate was acidified with hydrochloric acid (100 ml) slowly at 25-30C. The contents were stirred at 60C for 1 hour. The reaction mass was chilled to 0-5C and filtered to remove tritanol. The reaction mass was concentrated under reduced pressure. The residue was quenched with water (500ml), neutralized with base and extracted in dichloromethane (500 ml). The clear dichloromethane extract was then concentrated under reduced pressure and stripped off with acetone. The residue thus obtained was isolated from acetone (250 ml) to give 55 gms of the title compound. Chromatographic purity- > 99%; Example 2Preparation of olmesartan medoxomilTo dimethyl acetamide (600 ml) was added 4-(1-hydroxy-1-methylethyl)-2-propyl imidazol- 5-carboxylic acid ethyl ester (100 gms) and powdered potassium hydroxide (50 gms). To this was charged 4-[2-(trityltetrazol-5-yl)phenyl]benzyl bromide (270 gms) at 45-50C. The contents were stirred for 5 hours at 45-50C. Diisopropylethyl amine (200 ml) was charged to the reaction mass at 40-450C. To this was slowly added a solution of 5-methyl-2-oxo- 1 ,3-dioxane-4-yl)methyl chloride (160 gms) diluted with dimethyl acetamide (320 ml) at 40- 45C over a period of 1 hour. The contents were heated to 60-650C and maintained for 4 hours. The reaction mass was then cooled to 30-350C and was neutralized with concentrated hydrochloride acid. The reaction mass was filtered to remove inorganic impurities. The reaction mass was charcoalized using charcoal (20 gms) and was stirred for 30 minutes at 40-450C. The reaction mass was filtered over hyflo. The clear filtrate was acidified with hydrochloric acid (200 ml) slowly at 25-300C. The contents were stirred at 60C for 1 hour. The reaction mass was chilled to 0-50C and was filtered to remove tritanol. The reaction mass was concentrated under reduced pressure. The residue was quenched with water (1000 ml), neutralized with base and extracted in dichloromethane (1000 ml). The clear dichloromethane extract was then concentrated under reduced pressure, stripped off with acetone. The residue thus obtained was isolated from the acetone (500 ml) to give 110 gms of the title compound. Chromatogrphic purity- > 99%; Example 4Preparation of trityl olmesartan medoxomilTo dimethyl acetamide (300 ml) was added 4-(1-hydroxy-1-methylethyl)-2-propyl imidazol- 5-carboxylic acid ethyl ester (50 gms) and powdered potassium hydroxide (25 gms). To this was charged 4-[2-(trityltetrazol-5-yl)phenyl]benzyl bromide (135 gms) at 45-500C. The contents were stirred for 5 hours at 45-500C. Diisopropylethyl amine (100 ml) was charged to the reaction mass at 40-45C. To this was slowly added a solution of 5-methyl-2-oxo- 1 ,3-dioxane-4-yl) methyl chloride (80 gms) diluted with dimethyl acetamide (160 ml) at 40- 45C over a period of 1 hour. The contents were heated to 60-650C and maintained for 4 hours. The reaction mass was then cooled to 30-350C. and was neutralized with concentrated hydrochloride acid. The reaction mass was filtered to remove inorganics. The reaction mass was charcoalized using charcoal (10 gms) and was stirred for 30 minutes at 40-450C. The reaction mass was filtered over hyflo. The clear filtrate was quenched with purified water(200 ml)at 25-30C over a period of 3-4 hours. The contents were stirred at 25-300C for 30 minutes. Crude trityl olmesartan medoxomil was isolated by filtration, slurried in water (500 ml), centrifuged and dried under reduced pressure at 45-50C.

The chemical industry reduces the impact on the environment during synthesis, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; CIPLA LIMITED; CURTIS, Philip, Anthony; WO2008/43996; (2008); A2;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem