80841-78-7 | Page 27 of 43 | Dioxole related

Application of 80841-78-7

Elementary reactions that involve the simultaneous collision of more than three molecules are highly improbable and have never been observed experimentally.

An elementary termolecular reaction involves the simultaneous collision of three atoms, molecules, or ions.4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, cas is 80841-78-7. Here is a downstream synthesis route of the compound 80841-78-7, 80841-78-7

1L glass reaction flask was added with 600ml of acetone, 114.8g of intermediate 1 was added with stirring, then 12.8g of sodium hydroxide was added, the temperature was raised to 50-60 C, and the reaction was incubated for 5 hours, and the reaction was monitored by HPLC. To 20-30 C, add 2.8g potassium iodide, 36.0g 4-chloromethyl-5-methyl-1,3-dioxol-2-one, and increase the temperature to 50-60 C after the addition After 1 hour of heat preservation reaction, the temperature was lowered to 20-30 C, filtered, and the filter cake was rinsed with 115 ml of acetone, and the filtrate was combined. The filtrate was concentrated under reduced pressure at 40-50 C until no obvious solvent flowed out, and 320 ml of acetonitrile was added to cool down. The mixture was decanted to 20-30 C for 1 hour, filtered, and the filter cake was rinsed with 320 ml of acetonitrile. The filter cake was blast dried at 40-50 C for 12 hours to obtain a white solid 110.0 g (intermediate 2). The rate was 85.8%, HPLC: 99.2%.

Elementary reactions that involve the simultaneous collision of more than three molecules are highly improbable and have never been observed experimentally.

Reference£º
Patent; Jiashi (Hunan) Pharmaceutical Technology Co., Ltd.; Dai Yongzhi; Liu Hu; Zhu Laifa; Cai Jian; (8 pag.)CN108341804; (2018); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

Derivation of elementary reaction about 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one

Elementary reactions that involve the simultaneous collision of more than three molecules are highly improbable and have never been observed experimentally.

Rate laws may be derived directly from the chemical equations for elementary reactions. This is not the case, however, for ordinary chemical reactions.80841-78-7, molecula formula is 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, below Introduce a new synthetic route., 80841-78-7

Example 3; Trityl olmesartan medoxomil (III); A solution of potassium salt 4 in methyl ethyl ketone from the preceding experiment (ca. 20 g of the salt) was diluted with methyl ethyl ketone (290 ml), and, after adding potassium iodide (2 g) and 4-chloromethyl-5-methyl-l,3-dioxol-2-one (7 g), the mixture was stirred at 50 0C for 7.5 h. After the reaction was completed, the mixture was filtered, and the filtrate was washed with methyl ethyl ketone (3 x 50 ml). After concentrating to ca. 160 ml in vacuo, ethanol (250 ml) was added, and the reaction mixture was again concentrated to ca. 300 ml in vacuo.The concentrated product in ethanol was inoculated and stirred at 50 0C for 0.5 h, and after getting thicker, diluted with ethanol (50 ml) and cooled to 20 C. The precipitated product was sucked off, washed with ethanol (2 x 20 ml) and dried in a vacuum drier at 50 C. 14.4 g (86 %) of the product was obtained.

Elementary reactions that involve the simultaneous collision of more than three molecules are highly improbable and have never been observed experimentally.

Reference£º
Patent; ZENTIVA, A.S.; WO2007/48361; (2007); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

Sources of common compounds: 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one

With the complex challenges of chemical substances, we look forward to future research findings about 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one

The molecularity is the number of molecules that collide during that step in the mechanism. If only a single reactant molecule in an elementary reaction, that step is designated as unimolecular; if there are two reactant molecules, it is bimolecular.80841-78-7. A new synthetic method of this compound is introduced below., 80841-78-7

Example 7; Preparation of Trityl Olmesartan Medoxomil4-(1-Hydroxy-1-methylethyl)-2-propyl-1-{4-[2-(trityltetrazol-5-yl)phenyl]phenyl}methylimidazole-5-carboxylic acid dehydrate (100 g) was suspended in acetone (1 L) & heated to reflux; the solution obtained was added to suspension of potassium carbonate (15 g), potassium iodide (6 g) & 4-chloromethyl-5-methyl-1,3-dioxol-2-one (35 g) in acetone (500 mL) at reflux temperature. Reaction mass was refluxed for 2-6 hrs. After competition of reaction, the reaction mass was filtered & the acetone was distilled from combined mother liquor. The residue obtained was dissolved in toluene (1 L) toluene layer was washed with brine (3¡Á250 mL). Toluene was removed under reduced pressure & residue thus obtained was recrystallized from methanol to give trityl OlmesartanMedoxomil (100 g).HPLC purity=99.5%

With the complex challenges of chemical substances, we look forward to future research findings about 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one

Reference£º
Patent; Ramanjaneyulu, Gorantla Seeta; Mohan, Bandari; Ray, Purna Chandra; Sethi, Madhuresh Kumar; Rawat, Vijendra Singh; Krishna, Yerramalla Raja; Lakshminarayana, Vemula; Srinivas, Mamidi; US2009/281327; (2009); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

A new synthetic route of 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one

This molecular description is the mechanism of the reaction; it describes how individual atoms, ions, or molecules interact to form particular products. The stepwise changes are collectively called the reaction mechanism.

One of the major reasons is to use measurements of the macroscopic properties of a system, the rate of change in the concentration of reactants or products with time, to discover the sequence of events that occur at the molecular level. 80841-78-7, introduce a new downstream synthesis route. 80841-78-7

Example 236.0 g (50.3 mmol) ethyl 4-(1-hydroxy-1-methylethyl)-2-propyl-1-{4-[2-(trityltetrazol-5-yl)-phenyl]phenyl}-methyl imidazole-5-carboxylate (Va) and 3.0 g (75.4 mmol) of NaOH were suspended in 413 ml dimethylacetamide. The suspension was then stirred at room temperature for 20 h and after that 6.9 g (50.3 mmol) of K2CO3, were added. The mixture was cooled to 0 C. and solution of 15.4 g (70.4 mmol) 4-chloromethyl-5-methyl-2-oxo-1,3-dioxolene in 39 ml of dimethylacetamide were slowly added. The mixture was slowly heated to 50 C. and stirred at this temperature for 2 h. After esterification was completed, the mixture was cooled to 10 C. and poured into a mixture of 625 ml of ethyl acetate and 625 ml of 10% NaCl, and stirred at 25 C. for 15 min. The phases were separated and organic phase was washed 2¡Á with 500 ml of 10% NaCl, dried over Na2SO4 and filtered. The filtrate was concentrated up to ? (approximately 270 g) at reduced pressure.To the resulting solution, 80 ml of ethanol and 8.3 ml (100 mmol) of conc. HCl were added and stirred at 24-26 C. for 3 h. To the cooled mixture 600 ml of water was added and pH of the suspension was estimated to 5 by addition of 5 M NaOH. The phases were stirred for 15 min and separated. Water phase was reextracted with 150 ml of ethyl acetate. Collected organic phases were dried over Na2SO4, filtered and concentrated under reduced pressure. 560 ml of ethyl acetate were added and the mixture was evaporated again. After that, 300 ml of ethyl acetate were added and the mixture was cooled to 20 C. and stirred for 1 h, filtered off and washed with 20 ml of fresh ethyl acetate. The yield of the product (I) was 21 g (75%).

Reference£º
Patent; KRKA; US2009/131680; (2009); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

Application of 80841-78-7

Elementary reactions that involve the simultaneous collision of more than three molecules are highly improbable and have never been observed experimentally.

Example 1(1) Tritylation and DMDO Esterification ReactionsAfter mixing 4-(1-hydroxy-1-methylethyl)-2-propyl-1-[[2′-[1H-tetrazol-5-yl]biphenyl-4-yl]methyl]imidazole-5-carboxylic acid (30 g), acetone (210 mL), 1,8-diazabicyclo[5,4,0]-7-undecene [DBU] (25.5 g) and triphenylmethyl chloride [TPC] (23.79 g), water (0.6 mL) was added and acetone (30 mL) was poured into the mixture, and the reaction mixture was stirred at 48 to 52 C. for 2 hours. Then, water (0.9 mL) was added and 4-chloromethyl-5-methyl-1,3-dioxol-2-one [DMDO-Cl] (18.5 g) was poured in, and the reaction mixture was stirred at 48 to 52 C. for 5 hours.(2) Obtaining Crude Crystals of Trityl Olmesartan Medoxomil (Acetone Solvate Crystals)After the reaction mixture was cooled to 20 C. to precipitate crystals, it was stirred at 15 to 25 C. for 40 minutes, and water (96 mL) was added dropwise over a period of 25 minutes, and then the reaction mixture was cooled to 0 to 5 C. and stirred for 30 minutes. The precipitated crystals were filtered out and washed with acetone-water (150 mL), and wet crude crystals of (5-methyl-2-oxo-1,3-dioxolen-4-yl)methyl 4-(1-hydroxy-1-methylethyl)-2-propyl-1-[[2′-[2-(triphenylmethyl)-2H-tetrazol-5-yl]biphenyl-4-yl]methyl]imidazole-5-carboxylate (57.83 g) were obtained. These were then dried in vacuo at 60 C. for approximately 15 hours, and the dry acetone solvate crystals (57.50 g) were obtained.

Elementary reactions that involve the simultaneous collision of more than three molecules are highly improbable and have never been observed experimentally.

Reference£º
Patent; DAIICHI SANKYO COMPANY, LIMITED; US2012/59172; (2012); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

Research on new synthetic routes about 80841-78-7

There are, however, a few established termolecular elementary reactions. The reaction of nitric oxide with oxygen appears to involve termolecular steps.

A balanced equation for a chemical reaction indicates what is reacting and what is produced, but it reveals nothing about how the reaction actually takes place. The reaction mechanism is the process, or pathway, by which a reaction occurs.80841-78-7. An updated downstream synthesis route of 80841-78-7 as follows., 80841-78-7

Example 4; The reaction was carried out in the same manner as in Example 1 except that 4- (1-hydroxy-1-methylethyl) -2-propyl-1- {4- [2- (trityltetrazol-5-yl) phenyl] -carboxylic acid sodium salt (Chemical Formula 5) and 50 mL of N, N-dimethylacetamide were added, the temperature was adjusted to 5 to 10 DEG C and 4 g of potassium carbonate was added. A solution of 6.2 g of 4- (chloromethyl) -5-methyl-1,3-dioxol-2-one (Formula 6) in 6 mL of N, N-dimethylacetamide was added dropwise to the reaction portion, For 4 hours. After the reaction was completed, the reaction solution was cooled to 20 to 25 C, and then 220 mL of ethyl acetate, 30 g of salt, and 170 mL of purified water were sequentially added to the reaction mixture, followed by separation of the organic layer, followed by the addition of 30 g of salt and 170 mL of purified water . & Lt; / RTI & gt; 1 g of activated carbon and 20 g of anhydrous sodium sulfate were added to the organic layer, followed by stirring for 30 minutes to 1 hour, followed by filtration. The filtrate was concentrated under reduced pressure, and 100 mL of acetonitrile was added to the residue, followed by stirring at 50 to 55 DEG C for 1 hour. The crystals were cooled to 0 to 5 C., stirred for 2 hours, filtered, washed with 50 mL of isopropyl alcohol and dried to obtain 21.7 g (yield: 93%, purity: 99.96%) of tritylolemethanemethoxysilane

There are, however, a few established termolecular elementary reactions. The reaction of nitric oxide with oxygen appears to involve termolecular steps.

Reference£º
Patent; DONGBANG FTL CO., LTD; Song, Tae Hong; Jung, Hun Suk; Jang, Do Yeon; Moon, Chung Sun; Jung, Hee Jung; (18 pag.)KR101526249; (2015); B1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

The important role of 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one

The chemical industry reduces the impact on the environment during synthesis, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, , I believe this compound will play a more active role in future production and life.

80841-78-7, The molecularity is the number of molecules that collide during that step in the mechanism. If only a single reactant molecule in an elementary reaction, that step is designated as unimolecular; if there are two reactant molecules, it is bimolecular.80841-78-7. A new synthetic method of this compound is introduced below.

Extracurricular laboratory: Synthetic route of 80841-78-7

There are, however, a few established termolecular elementary reactions. The reaction of nitric oxide with oxygen appears to involve termolecular steps.

80841-78-7, A balanced equation for a chemical reaction indicates what is reacting and what is produced, but it reveals nothing about how the reaction actually takes place. The reaction mechanism is the process, or pathway, by which a reaction occurs.80841-78-7. An updated downstream synthesis route of 80841-78-7 as follows.

There are, however, a few established termolecular elementary reactions. The reaction of nitric oxide with oxygen appears to involve termolecular steps.

Reference£º
Patent; DAIICHI SANKYO COMPANY, LIMITED; US2012/59172; (2012); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

The important role of 80841-78-7

Chemical properties determine the actual use. Each compound has specific chemical properties and uses. We look forward to more synthetic routes in the future to expand 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one reaction routes.

Example 2; 36.0 g (50.3 mmol) ethyl 4-(1-hydroxy-1-methylethyl)-2-propyl-1-(4-[2-(trityltetrazol-5-yl)-phenyl]phenyl}-methyl imidazole-5-carboxylate (Va) and 3.0 g (75.4 mmol) of NaOH were suspended in 413 ml dimethylacetamide. The suspension was then stirred at room temperature for 20 h and after that 6.9 g (50.3 mmol) of K2CO3 were added. The mixture was cooled to 0C and solution of 15.4 g (70.4 mmol) 4-chloromethyl-5-methyl-2-oxo-1,3-dioxolene in 39 ml of dimethylacetamide were slowly added. The mixture was slowly heated to 50C and stirred at this temperature for 2 h. After esterification was completed, the mixture was cooled to 10 C and poured into a mixture of 625 ml of ethyl acetate and 625 ml of 10 % NaCl, and stirred at 25 C for 15 min. The phases were separated and organic phase was washed 2x with 500 ml of 10 % NaCl, dried over Na2SO4 and filtered. The filtrate was concentrated up to ? (approximately 270 g) at reduced pressure. To the resulting solution, 80 ml of ethanol and 8.3 ml (100 mmol) of conc. HCl were added and stirred at 24-26C for 3h. To the cooled mixture 600 ml of water was added and pH of the suspension was estimated to 5 by addition of 5 M NaOH. The phases were stirred for 15 min and separated. Water phase was reextracted with 150 ml of ethyl acetate. Collected organic phases were dried over Na2SO4, filtered and concentrated under reduced pressure. 560 ml of ethyl acetate were added and the mixture was evaporated again. After that, 300 ml of ethyl acetate were added and the mixture was cooled to 20 C and stirred for 1h, filtered off and washed with 20 ml of fresh ethyl acetate. The yield of the product (I) was 21 g (75 %).

Reference£º
Patent; KRKA, tovarna zdravil, d.d., Novo mesto; EP1816131; (2007); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

New learning discoveries about 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one

There are, however, a few established termolecular elementary reactions. The reaction of nitric oxide with oxygen appears to involve termolecular steps.

Example 5: The reaction part was charged with ethyl 4- (1-hydroxy-1-methylethyl) -2-propyl-1- {4- [2- (trityltetrazol-5-yl) phenyl] 22 g of 5-carboxylate (Formula 4), 3.1 g of sodium hydroxide and 90 mL of ethanol were added and the mixture was stirred at 20 to 25 C for 4 to 5 hours. When the reaction was completed, the reaction solution was concentrated. To the residue were added 50 mL of ethyl acetate and 50 mL of purified water. The mixture was stirred for 1 hour and then layered. The separated organic layer was washed twice with an aqueous solution containing 30 g of salt and 170 mL of purified water. 1 g of activated carbon and 20 g of anhydrous sodium sulfate were added to the organic layer, followed by stirring for 30 minutes to 1 hour, followed by filtration Respectively. After the filtrate was concentrated under reduced pressure, 50 mL of N, N-dimethylacetamide was added to the residue, the temperature was adjusted to 5 to 10 DEG C 4 g of potassium carbonate was added and 6.2 g of 4- (chloromethyl) -5-methyl-1,3-dioxol-2-one (Formula 6) was dissolved in N, N-dimethylacetamide 6 ML was added dropwise, and the mixture was reacted at 45 to 50 C for 4 hours with stirring. When the reaction is completed, the reaction solution is cooled to 20 to 25 After cooling, 220 mL of ethyl acetate, 30 g of salt and 170 mL of purified water were added successively. The organic layer was separated And then washed once more with an aqueous solution containing 30 g of salt and 170 mL of purified water. The organic layer was washed with 1 g of activated carbon, 20 g of sodium was added and stirred for 30 minutes to 1 hour, followed by filtration. The filtrate was concentrated under reduced pressure, and then acetone 100 mL of i-tril was added, and the mixture was stirred at 50 to 55 C for 1 hour. The crystals were cooled to 0 to 5 [deg.] C and stirred for 2 hours. Followed by washing with 50 mL of isopropyl alcohol, followed by drying to obtain 21.6 g (yield: 88%) of tritylolemecanemethoxysilane (formula 1a) Purity 99.97%) was obtained

There are, however, a few established termolecular elementary reactions. The reaction of nitric oxide with oxygen appears to involve termolecular steps.