80841-78-7 | Page 25 of 43 | Dioxole related

Share a compound : 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one

The chemical industry reduces the impact on the environment during synthesis, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, , I believe this compound will play a more active role in future production and life.

We know that the rate of many reactions can be accelerated by catalysts. A catalyst speeds up the rate of a reaction by lowering the activation energy; in addition, the catalyst is regenerated in the process. 80841-78-7, molecula formula is C5H5ClO3, below Introduce a new synthetic route., 80841-78-7

Step B, go to the reaction solution of compound (II) obtained in Step A with stirring,Add 6.27kg of anhydrous sodium carbonate powder and 2.01kg of iodine, replace the air with nitrogen,The nitrogen pressure in the kettle is ?0.01Mpa, the control temperature is 50 ¡À 2 ,15.05 kg of compound (IV) was added dropwise at a constant pressure, and the addition was completed within 40 to 60 minutes.After the reaction was held for 1 hour, the reaction mixture was reduced to below 10 C.Extract with conventional solvents in an extraction kettle, wash with water, and separate the layers.The organic phase was distilled under reduced pressure to recover the solvent, crystallized, centrifuged,After drying, 54.88 kg of the crude compound (I) was obtained.Step C: Add 192.08 kg of ethyl acetate to the 500L refining kettle, start stirring,Add 54.88 kg of crude compound (I) obtained in step B, close the feed port,Keep the pressure ?0.01MPa after replacing air with nitrogen,The temperature was raised to 75 C and dissolved for 25 minutes until it was clear. The filtrate was filtered and the temperature was reduced to 2.5 C.Centrifuge, put the filter cake into the double cone dryer,Under reduced pressure, a small flow of nitrogen was passed in for replacement three times, and the drying temperature was controlled to 40-50 C.Vacuum degree ?-0.09MPa, after drying for 1 hour,Increase the drying temperature to 50 60 and continue drying for 3 hours.After cooling down, 53.60 kg of compound (1) was obtained, and the HPLC content was 99.87%.Compound (III) had a residual content of 0.06%.

Reference£º
Patent; Shandong Xinhua Pharmaceutical Co., Ltd.; Zhu Lianbo; Wu Hui; Dou Guohua; (6 pag.)CN110590758; (2019); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

Some tips on 80841-78-7

The molecularity is the number of molecules that collide during that step in the mechanism. If only a single reactant molecule in an elementary reaction, that step is designated as unimolecular; if there are two reactant molecules, it is bimolecular.80841-78-7. A new synthetic method of this compound is introduced below., 80841-78-7

Step B, go to the reaction solution of compound (II) obtained in Step A with stirring,Add 6.27kg of anhydrous potassium carbonate powder and2.01kg iodine, replace the air with nitrogen, the nitrogen pressure in the kettle is ?0.01Mpa,The temperature was controlled at 50 ¡À 2 , and 13.80 kg of compound (IV) was added dropwise at a constant pressure.Add within 40 to 60 minutes. After the incubation reaction for 1.25 hours,Reduce the reaction mixture to below 10 C, extract with conventional solvents in an extraction kettle, wash with water, and separate the layers.The organic phase was distilled under reduced pressure to recover the solvent, crystallized, centrifuged,Drying gave 55.03 kg of crude compound (I).Step C: Add 192.61 kg of ethyl acetate to the 500L refining kettle, start stirring,55.03 kg of the crude compound (I) obtained in step B is added, and the feeding port is closed,Keep the pressure ?0.01MPa after replacing air with nitrogen,The temperature was raised to 75 C and dissolved for 25 minutes until it was clear. The filtrate was filtered and the temperature was reduced to 2.5 C.Centrifuge, put the filter cake into the double cone dryer,Under reduced pressure, a small flow of nitrogen was passed in for replacement three times, and the drying temperature was controlled to 40-50 C.Vacuum degree ?-0.09MPa, after drying for 1 hour,Increase the drying temperature to 50 60 and continue drying for 3 hours.54.06kg compound (1) finished product,The HPLC content was 99.93%, and the residual content of the compound (III) was 0.05%.

Reference£º
Patent; Shandong Xinhua Pharmaceutical Co., Ltd.; Zhu Lianbo; Wu Hui; Dou Guohua; (6 pag.)CN110590758; (2019); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

Derivation of elementary reaction about 80841-78-7

Elementary reactions that involve the simultaneous collision of more than three molecules are highly improbable and have never been observed experimentally.

Rate laws may be derived directly from the chemical equations for elementary reactions. This is not the case, however, for ordinary chemical reactions.80841-78-7, molecula formula is 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, below Introduce a new synthetic route., 80841-78-7

The reaction flask was charged with 697.5 g of compound V obtained in the previous step,414 g of anhydrous potassium carbonate (3.00 mol)163.4 g of 4-chloromethyl-5-methyl-1,3-dioxol-2-one (Compound VI) (1.10 mol)And 2500 ml of acetonitrile were refluxed for 2 hours,After the reaction,filter,The filtrate was concentrated to dryness,The residue was stirred in 1500 ml of ethyl acetate and 500 ml of water for 15 minutes,Layered, organic layer and then washed with water,Dried over anhydrous sodium sulfate,filter,The filtrate was concentrated to dryness,To give the crude product of compound VII,Recrystallization from toluene and petroleum ether,To obtain pure product 683.2 grams; two-step yield:85.40% (calculated as compound II).

Elementary reactions that involve the simultaneous collision of more than three molecules are highly improbable and have never been observed experimentally.

Reference£º
Patent; Hunan Ouya biological Co. Ltd.; Lin, kaizhao; (19 pag.)CN103304550; (2016); B;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

Some tips on 80841-78-7

Reference£º
Patent; Hunan Ouya biological Co. Ltd.; Lin, kaizhao; (19 pag.)CN103304550; (2016); B;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

Share a compound : 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one

A balanced equation for a chemical reaction indicates what is reacting and what is produced, but it reveals nothing about how the reaction actually takes place. The reaction mechanism is the process, or pathway, by which a reaction occurs.80841-78-7. An updated downstream synthesis route of 80841-78-7 as follows., 80841-78-7

Example 2; 36.0 g (50.3 mmol) ethyl 4-(l -hydroxy- 1-methy lethyl)-2-propy 1-1- {4-[2-(trityltetrazol-5-y I)- phenyl]phenyl} -methyl imidazole-5-carboxylate (Va) and 3.0 g (75.4 mmol) of NaOH were suspended in 413 ml dimethylacetamide. The suspension was then stirred at room temperature for 20 h and after that 6.9 g (50.3 mmol) of K2CO3, were added. The mixture was cooled to 00C and solution of 15.4 g (70.4 mmol) 4-chloromethyl-5-methyl-2-oxo-l,3- dioxolene in 39 ml of dimethylacetamide were slowly added. The mixture was slowly heated to 500C and stirred at this temperature for 2 h. After esterification was completed, the mixture was cooled to 10 0C and poured into a mixture of 625 ml of ethyl acetate and 625 ml of 10 % NaCl, and stirred at 25 0C for 15 min. The phases were separated and organic phase was washed 2chi with 500 ml of 10 % NaCl, dried over Na2SO4 and filtered. The filtrate was concentrated up to 14 (approximately 270 g) at reduced pressure.To the resulting solution, 80 ml of ethanol and 8.3 ml (100 mmol) of cone. HCl were added EPO and stirred at 24-26C for 3h. To the cooled mixture 600 ml of water was added and pH of the suspension was estimated to 5 by addition of 5 M NaOH. The phases were stirred for 15 min and separated. Water phase was reextracted with 150 ml of ethyl acetate. Collected organic phases were dried over Na2SO4, filtered and concentrated under reduced pressure. 560 ml of ethyl acetate were added and the mixture was evaporated again. After that, 300 ml of ethyl acetate were added and the mixture was cooled to 20 0C and stirred for Ih, filtered off and washed with 20 ml of fresh ethyl acetate. The yield of the product (I) was 21 g (75 %).

Reference£º
Patent; KRKA; WO2007/17135; (2007); A2;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

Extracurricular laboratory: Synthetic route of 80841-78-7

A chemical reaction often occurs in steps, although it may not always be obvious to an observer.

80841-78-7, A balanced equation for a chemical reaction indicates what is reacting and what is produced, but it reveals nothing about how the reaction actually takes place. The reaction mechanism is the process, or pathway, by which a reaction occurs.80841-78-7. An updated downstream synthesis route of 80841-78-7 as follows.

To a solution of the compound of Formula IV (5.0 g) in toluene (40 mL), dimethylacetamide (10 mL) is added, followed by addition of sodium hydroxide (1.2 g) and N,N-diisopropylamine (3.7 g) at 25-35C. The mixture is stirred at 40- 45C for 4 hours. 5-Methyl-2-oxo-(1 ,3-dioxolene-4-yl)methyl chloride (1.5 g) and tetrabutylammonium bromide (0.5 g) are added at 40-450C. The mixture is stirred at 60-70C for 8 hours. The mass is cooled to 25-35C, water (50 mL) is added, and the pH is adjusted to about 6-7 by adding 10% aqueous HCI. The layers are separated. The aqueous layer is extracted with toluene (25 mL). The organic layers are combined and washed with water (25 mL). The solvent is distilled under reduced pressure. Methanol (25 mL) is added to the residue. The mixture is cooled to 0-50C and stirred at that temperature for 45 minutes. The formed solid is filtered, washed with methanol (10 mL) and dried for 45 minutes under vacuum (yield 3.0 g).

A chemical reaction often occurs in steps, although it may not always be obvious to an observer.

Reference£º
Patent; DR. REDDY’S LABORATORIES LTD.; DR. REDDY’S LABORATORIES, INC.; KOLLA, Naveen Kumar; MANNE, Nagaraju; NAREDLA, Anitha; SHINDE, Sachin Gulabrao; WO2011/14611; (2011); A2;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

Some scientific research about 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one

Toluene (180 L) is placed into a reactor and water (3.17 L) is added, followed by addition of ethyl-4-(1 -hydroxy-1 -methylethyl)-2-propylimidazole-5- carboxylate (18.0 Kg). The mass is stirred for about 10 minutes, heated to about 45C, and potassium carbonate (25.85 Kg) is added. The temperature of the mass is raised to about 65C and maintained for about 45 minutes. N-(triphenylmethyl)- 5-[4′-(bromomethyl)biphenyl-2-yl]tetrazole (48.9 Kg) and tetrabutylammonium bromide (4.82 Kg) are added at the same temperature and the mixture is stirred at 60-700C for 10 hours. Reaction completion is verified using thin layerchromatography (TLC). After the reaction is complete, the mass is washed with water (3*120 L) at about 500C. The mass is cooled to about 25C and toluene (468 L) and potassium tertiary-butoxide (12.6 Kg) is added, then the mass is maintained at the same temperature for about 1 hour. Water (0.85 L) is added and the mass is maintained at the same temperature for about 2 hours. Reaction completion is verified using TLC, then 5-methyl-2-oxo-(1 ,3-dioxolene-4-yl)methyl chloride (20 Kg), tetrabutylammonium bromide (4.82 Kg), and sodium carbonate (3.96 Kg) are added at 40-450C. The mass is stirred at about 55C for about 11 hours. After the reaction is complete, the mass is cooled to about 20C, water (540 L) is added and the pH is adjusted to about 6-7 by adding 10% aqueous HCI. The layers are separated. The aqueous layer is extracted with toluene (240 L). The organic layers are combined and washed with water (270 L). The solvent is distilled under reduced pressure. Acetone (189 L) is added to the residue and the mixture is heated to about 45C to produce a solution, then the solution is cooled to about 300C and maintained for about 20 minutes, followed by cooling to about 2C and maintaining for about 3 hours. The formed solid is filtered, washed with acetone (54 L), and dried for about 4 hours. The material obtained is re- crystallized from acetonitrile to yield 34.0 Kg of the title compound.

Extended knowledge of 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one

A chemical reaction often occurs in steps, although it may not always be obvious to an observer.

188.0kg of tetrahydrofuran was added to a glass-lined reactor, 54.0kg 4- (1- hydroxy-1-methylethyl) -2-propyl-1- {4- [2- (trityl-tetrazol -5 – yl) phenyl] phenyl} methylimidazole-5-carboxylate, 92.0.0kg 4.0kg purified water and lithium hydroxide monohydrate.After complete addition, 20 stirred for 18 hours, once every 2 hours the reaction temperature recording, tracking and detection TLC starting material to substantially complete the reaction.After completion of the reaction, 240.0kg Ethyl acetate and sodium chloride solution (20.0 kg of sodium chloride was added to 180.0kg purified water, and dissolved with stirring), stirred for 10 minutes, allowed to stand for 20 minutes stratification.The organic phase was washed with sodium chloride solution (32.0 kg of sodium chloride was added to 288.0kg purified water, stirred and dissolved) Average washed twice, each wash was stirred for 10 minutes and allowed to stand for 20 minutes.The organic phase was collected, dried over anhydrous sodium sulfate and stirred for 4 hours.Filtered, and the filtrate was concentrated under reduced pressure to remove ethyl acetate (water bath temperature controlled at 45 ¡À 5 , the degree of vacuum at -0.1 ~ -0.06MPa), a solution 188.0kg N, N- dimethylformamide, is added 15.3kg anhydrous potassium carbonate, 2.7kg of potassium iodide was stirred at 20 ¡À 10 was slowly added 14.5kg 4- chloro-5-methyl-1,3-dioxol-2-one, addition was completed, heating, feed temperature control reaction was stirred for 2 hours at 40 ¡À 2 .After completion of the reaction, the material was cooled to 15 ¡À 5 rejection filter, and the filtrate was added to a solution of sodium chloride (338.0kg sodium chloride to 940.0kg purified water, and dissolved with stirring), the following -5 ~ 0 stirred for 4h, rejection was filtered, the filter cake was charged to an oven baking pan blast drying oven at a temperature of 40 ¡À 5 8 hours.To give 58.2kg of trityl olmesartan medoxomil, a yield of 96.5%.

A chemical reaction often occurs in steps, although it may not always be obvious to an observer.

Reference£º
Patent; Lianyungang Runzhong Pharmaceutical Co., Ltd.; Zhong Zhaobo; Cheng Jinrong; He Shaojie; Tang Zhaocheng; (6 pag.)CN110396084; (2019); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

New learning discoveries about 80841-78-7

There are, however, a few established termolecular elementary reactions. The reaction of nitric oxide with oxygen appears to involve termolecular steps.

To the flask was added 2000 g of acetone, 160 g of ethyl 4- (1-hydroxy-1-methylethyl) -2-propylimidazole-5-carboxylate (II), 150 g of K2CO3, 460 g of 4- [2- (Trityltetrazol-5-yl) phenyl] benzyl bromide (III), 20g KI, the temperature was raised to reflux, the reaction was incubated for 34-38 hours under stirring.Then add 102g KOH, reflux reaction 6 ~ 8h. Cool to 10 ~ 20 , add 170g DMDO-Cl, incubated for 30 ~ 60min.Heating to reflux, the reaction 22 to 26 hours.After the reaction was added 40g of diatomaceous earth, stirring for 30 to 60 minutes, suction filtration, 200g acetone rinse cake. To the filtrate was added 800g of drinking water and 200g of refined hydrochloric acid, the reaction at room temperature for 2 to 4 hours, filtered to remove by-product triphenylcarbinol. Dropping 10% K2CO3 aqueous solution, adjusting feedstock pH to 4, cooling to 10 ~ 20 , stirring crystallization 2h, filtration, the filter cake with a mixture of pre-cooled 45g acetone and 230g of drinking water washing and drying, to obtain Olmesartan Medoxomil 309 g, total yield 83.1% (relative to ethyl-4- (1-hydroxy-1-methylethyl) -2-propylimidazole-5- carboxylate (II)), purity: 99.27% of the main peak, 0.08% of the olmesartan acid, 0.14% of the triphenylmethanol, and 0.13% of the largest unidentified one.

There are, however, a few established termolecular elementary reactions. The reaction of nitric oxide with oxygen appears to involve termolecular steps.

Reference£º
Patent; Zhejiang Huahai Zhicheng Pharmaceutical Co., Ltd.; Zhejiang Huahai Pharmaceutical Co., Ltd.; Jin Congyang; Wang Jiquan; Zhang Wenling; Wang Peng; (10 pag.)CN107311990; (2017); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

Extracurricular laboratory: Synthetic route of 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one

A chemical reaction often occurs in steps, although it may not always be obvious to an observer.

130 ml of N,N-dimethylacetamide, 14.0 g (20 mmol) of ethyl 4-(2-hydroxypropan-2-yl)-2-propyl-1-((2′-(1-trityl-1H-tetrazol-5-yl)biphenyl-4-yl)methyl)-1H-imidazole-5-carboxylate and 2.2 g (16 mmol) of KOH were charged into reaction vessel at room temperature under inert atmosphere. The mixture was stirred at room temperature for 2 h, and then the sample of reaction mixture was analysed (HPLC; starting material 0.2 %, hydrolysed starting material 98.11 %). Then 3.0 g (2.2 mmol) of potassium carbonate powder and 1.4 g (8.4 mmol) of potassium iodide were added. The reaction mixture was cooled to 0 C and 5.0 g (33 mmol) of 4-(chloromethyl)-5-methyl-1,3-dioxol-2-one was added at 0 to 5C. After the addition, the reaction mixture was warmed to 40-45 C within one hour, then the mixture was stirred at this temperature for 2h. The sample of reaction mixture was analysed (HPLC; tritylolmesartan medoxomil 97.22 %, 4-(2-hydroxypropan-2-yl)-2-propyl-1-((2′-(1-trityl-1H-tetrazol-5-yl)biphenyl-4-yl)methyl)-1H-imidazole-5-carboxylate 0.09 %). The mixture was cooled to 10 to 20 C and then 250 ml of ethyl acetate was added. The mixture was cooled again to 5-10 C and then 200 ml of 10 % NaCl was added slowly. The temperature should not be higher than 25 C during the addition. The phases were mixed separated and organic phase was washed with 100 ml of 10 % NaCl (2*) and dried over anhydrous sodium sulphate. After the filtration filtrate was evaporated under reduced pressure at temperature under 45C to oily residue. To the residue 30 ml of acetonitrile was added at temperature not more than 45C. The mixture was stirred at this temperature for 10 minutes then was cooled to 20 to 25C and stirred at this temperature for 0.5 h and after that 3h at 0 to 5C. The suspension was filtered, the cake washed with cold acetonitrile and dried at 40 to 50C. Yield: 17.0 g (94%) HPLC: 99.72 % of the product, all impurities are under 0.1%. IR: 3408, 1818, 1805, 1741, 1681, 1529, 1147, 1003, 699 XRD:

A chemical reaction often occurs in steps, although it may not always be obvious to an observer.

Reference£º
Patent; Krka Tovarna Zdravil, D.D., Novo Mesto; EP2334668; (2011); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem