Category: 80841-78-7

80841-78-7, The molecularity is the number of molecules that collide during that step in the mechanism. If only a single reactant molecule in an elementary reaction, that step is designated as unimolecular; if there are two reactant molecules, it is bimolecular.80841-78-7. A new synthetic method of this compound is introduced below.

The reaction flask was charged with 697.5 g of compound V obtained in the previous step,414 g of anhydrous potassium carbonate (3.00 mol)163.4 g of 4-chloromethyl-5-methyl-1,3-dioxol-2-one (Compound VI) (1.10 mol)And 2500 ml of acetonitrile were refluxed for 2 hours,After the reaction,filter,The filtrate was concentrated to dryness,The residue was stirred in 1500 ml of ethyl acetate and 500 ml of water for 15 minutes,Layered, organic layer and then washed with water,Dried over anhydrous sodium sulfate,filter,The filtrate was concentrated to dryness,To give the crude product of compound VII,Recrystallization from toluene and petroleum ether,To obtain pure product 683.2 grams; two-step yield:85.40% (calculated as compound II).

Elementary reactions that involve the simultaneous collision of more than three molecules are highly improbable and have never been observed experimentally.

Reference£º
Patent; Hunan Ouya biological Co. Ltd.; Lin, kaizhao; (19 pag.)CN103304550; (2016); B;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

Rate laws may be derived directly from the chemical equations for elementary reactions. This is not the case, however, for ordinary chemical reactions.80841-78-7, molecula formula is 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, below Introduce a new synthetic route., 80841-78-7

Example 1-5 (0330) (0331) A mixture of BIC (0.6 g, 0.83 mmol), potassium iodide (0.069 g, 0.41 mmol), OXC (0.245 g, 1.65 mmol) and methyl ethyl ketone (9.0 mL, 15 vol) was stirred at 50 C. for 20 hr. The reaction mixture was filtered, the filtrate was concentrated under reduced pressure, and the obtained concentrated residue was purified by silica gel column chromatography (20-22% ethyl acetate/hexane) to give TOLM (650 mg, yield 84.4%). (0332) Mass: 801 [M+H]+, 824 [M+Na]+.

Elementary reactions that involve the simultaneous collision of more than three molecules are highly improbable and have never been observed experimentally.

Reference£º
Patent; API CORPORATION; Seki, Masahiko; US2015/239854; (2015); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

80841-78-7, The molecularity is the number of molecules that collide during that step in the mechanism. If only a single reactant molecule in an elementary reaction, that step is designated as unimolecular; if there are two reactant molecules, it is bimolecular.80841-78-7. A new synthetic method of this compound is introduced below.

Example 5; Preparation of trityl olmesartan medoxomilTo dimethyl sulphoxide (800 ml), sodium hydroxide powder (50 gms) was added under nitrogen atmosphere and stirred at 20-250C for 10 minutes. To this, 4-( 1 -hydroxy- 1- methylethyl)-2-propyl-imidazole-5-ethyl carboxylate (100 gms) was added at 20-250C. 5- (4′-bromomethyl-biphenyl)-2-yl-1 -trityl tetrazole (270 gms) was added slowly at 20-250C, and the reaction mass was stirred at 20-250C for 12 hours. Further 10% sodium hydroxide solution (100 ml) was added to the reaction mass at 20-250C. The temperature of the reaction mass was raised to 40-450C, the contents stirred at 40-450C for 2 hours and 5- methyl-2-oxo-1 ,3-dioxane-4-yl)methyl chloride (160 gms) was added slowly at 45-5O0C over a period of 45 minutes. The contents were stirred at 45-5O0C for 2 hours. The reaction mass was then cooled to 0-50C, stirred for 1 hour at 0-50C, filtered and slurried in water (1.0 It) at 40-450C for 1 hour, filtered at 4O0C and dried at 4O0C. To the dried material, ethyl acetate (2.5 It) was added, heated to 50-550C for complete dissolution, ethyl acetate was distilled off to 1.0 It stage under vacuum at 45-5O0C. The contents were cooled to 0-50C, stirred at 0-50C for 3 hours, filtered, washed with chilled methanol (100 ml) and dried under vacuum at 40-450C to give 250 gms of the title compound. Purity by HPLC : > 99%

This molecular description is the mechanism of the reaction; it describes how individual atoms, ions, or molecules interact to form particular products. The stepwise changes are collectively called the reaction mechanism.

Reference£º
Patent; CIPLA LIMITED; CURTIS, Philip, Anthony; WO2008/43996; (2008); A2;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

Rate laws may be derived directly from the chemical equations for elementary reactions. This is not the case, however, for ordinary chemical reactions.80841-78-7, molecula formula is 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, below Introduce a new synthetic route., 80841-78-7

Example 5; Preparation of trityl olmesartan medoxomilTo dimethyl sulphoxide (800 ml), sodium hydroxide powder (50 gms) was added under nitrogen atmosphere and stirred at 20-250C for 10 minutes. To this, 4-( 1 -hydroxy- 1- methylethyl)-2-propyl-imidazole-5-ethyl carboxylate (100 gms) was added at 20-250C. 5- (4′-bromomethyl-biphenyl)-2-yl-1 -trityl tetrazole (270 gms) was added slowly at 20-250C, and the reaction mass was stirred at 20-250C for 12 hours. Further 10% sodium hydroxide solution (100 ml) was added to the reaction mass at 20-250C. The temperature of the reaction mass was raised to 40-450C, the contents stirred at 40-450C for 2 hours and 5- methyl-2-oxo-1 ,3-dioxane-4-yl)methyl chloride (160 gms) was added slowly at 45-5O0C over a period of 45 minutes. The contents were stirred at 45-5O0C for 2 hours. The reaction mass was then cooled to 0-50C, stirred for 1 hour at 0-50C, filtered and slurried in water (1.0 It) at 40-450C for 1 hour, filtered at 4O0C and dried at 4O0C. To the dried material, ethyl acetate (2.5 It) was added, heated to 50-550C for complete dissolution, ethyl acetate was distilled off to 1.0 It stage under vacuum at 45-5O0C. The contents were cooled to 0-50C, stirred at 0-50C for 3 hours, filtered, washed with chilled methanol (100 ml) and dried under vacuum at 40-450C to give 250 gms of the title compound. Purity by HPLC : > 99%

Chemical properties determine the actual use. Each compound has specific chemical properties and uses. We look forward to more synthetic routes in the future to expand 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one reaction routes.

Reference£º
Patent; CIPLA LIMITED; CURTIS, Philip, Anthony; WO2008/43996; (2008); A2;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

We know that the rate of many reactions can be accelerated by catalysts. A catalyst speeds up the rate of a reaction by lowering the activation energy; in addition, the catalyst is regenerated in the process. 80841-78-7, molecula formula is C5H5ClO3, below Introduce a new synthetic route., 80841-78-7

(3) the C43 H39 N6 NaO3 AMST – 4 and DMF added in a reaction kettle, lowering the temperature to 0 C, adding potassium carbonate, maintain 0 C dropwise C5 H5 ClO3 AMST – 5 dissolved in DMF solution, after the completion of the dropping 85 C reaction 4 hours, monitoring the reaction is finished adding water, sodium chloride and ethyl acetate stirring extraction, liquid, separating the upper organic phase, a mixed solution of water and sodium chloride washing, separating the organic phase at upper layer for sodium sulfate drying, filtering, 60 C concentrated to the reagent, in acetonitrile for 30 C beating 1 hour, cooling to 25 C, filtering, cake isopropyl alcohol leaching, 75 C drying to constant weight to obtain the product C48 H44 N6 O6 AMST – 6; the C43 H39 N6 NaO3 AMST – 4, DMF, potassium carbonate, C5 H5 ClO3 AMST – 5, ethyl acetate, acetonitrile, water, sodium chloride and sodium sulfate the mass ratio of the 192:560: 62:1500: 1000:1500: 300:50;

With the complex challenges of chemical substances, we look forward to future research findings about 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one

Reference£º
Patent; Jiangxi Yong Tong Technology Co., Ltd.; Liu Zhongchun; (10 pag.)CN107311989; (2017); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

An elementary termolecular reaction involves the simultaneous collision of three atoms, molecules, or ions.4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, cas is 80841-78-7. Here is a downstream synthesis route of the compound 80841-78-7, 80841-78-7

Step B, go to the reaction solution of compound (II) obtained in Step A with stirring,Add 6.27kg of anhydrous potassium carbonate powder and2.01kg iodine, replace the air with nitrogen, the nitrogen pressure in the kettle is ?0.01Mpa,The temperature was controlled at 50 ¡À 2 , and 13.80 kg of compound (IV) was added dropwise at a constant pressure.Add within 40 to 60 minutes. After the incubation reaction for 1.25 hours,Reduce the reaction mixture to below 10 C, extract with conventional solvents in an extraction kettle, wash with water, and separate the layers.The organic phase was distilled under reduced pressure to recover the solvent, crystallized, centrifuged,Drying gave 55.03 kg of crude compound (I).Step C: Add 192.61 kg of ethyl acetate to the 500L refining kettle, start stirring,55.03 kg of the crude compound (I) obtained in step B is added, and the feeding port is closed,Keep the pressure ?0.01MPa after replacing air with nitrogen,The temperature was raised to 75 C and dissolved for 25 minutes until it was clear. The filtrate was filtered and the temperature was reduced to 2.5 C.Centrifuge, put the filter cake into the double cone dryer,Under reduced pressure, a small flow of nitrogen was passed in for replacement three times, and the drying temperature was controlled to 40-50 C.Vacuum degree ?-0.09MPa, after drying for 1 hour,Increase the drying temperature to 50 60 and continue drying for 3 hours.54.06kg compound (1) finished product,The HPLC content was 99.93%, and the residual content of the compound (III) was 0.05%.

The chemical industry reduces the impact on the environment during synthesis, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; Shandong Xinhua Pharmaceutical Co., Ltd.; Zhu Lianbo; Wu Hui; Dou Guohua; (6 pag.)CN110590758; (2019); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

An elementary termolecular reaction involves the simultaneous collision of three atoms, molecules, or ions.4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, cas is 80841-78-7. Here is a downstream synthesis route of the compound 80841-78-7, 80841-78-7

Example 236.0 g (50.3 mmol) ethyl 4-(1-hydroxy-1-methylethyl)-2-propyl-1-{4-[2-(trityltetrazol-5-yl)-phenyl]phenyl}-methyl imidazole-5-carboxylate (Va) and 3.0 g (75.4 mmol) of NaOH were suspended in 413 ml dimethylacetamide. The suspension was then stirred at room temperature for 20 h and after that 6.9 g (50.3 mmol) of K2CO3, were added. The mixture was cooled to 0 C. and solution of 15.4 g (70.4 mmol) 4-chloromethyl-5-methyl-2-oxo-1,3-dioxolene in 39 ml of dimethylacetamide were slowly added. The mixture was slowly heated to 50 C. and stirred at this temperature for 2 h. After esterification was completed, the mixture was cooled to 10 C. and poured into a mixture of 625 ml of ethyl acetate and 625 ml of 10% NaCl, and stirred at 25 C. for 15 min. The phases were separated and organic phase was washed 2¡Á with 500 ml of 10% NaCl, dried over Na2SO4 and filtered. The filtrate was concentrated up to ? (approximately 270 g) at reduced pressure.To the resulting solution, 80 ml of ethanol and 8.3 ml (100 mmol) of conc. HCl were added and stirred at 24-26 C. for 3 h. To the cooled mixture 600 ml of water was added and pH of the suspension was estimated to 5 by addition of 5 M NaOH. The phases were stirred for 15 min and separated. Water phase was reextracted with 150 ml of ethyl acetate. Collected organic phases were dried over Na2SO4, filtered and concentrated under reduced pressure. 560 ml of ethyl acetate were added and the mixture was evaporated again. After that, 300 ml of ethyl acetate were added and the mixture was cooled to 20 C. and stirred for 1 h, filtered off and washed with 20 ml of fresh ethyl acetate. The yield of the product (I) was 21 g (75%).

The chemical industry reduces the impact on the environment during synthesis, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; KRKA; US2009/131680; (2009); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

80841-78-7, The molecularity is the number of molecules that collide during that step in the mechanism. If only a single reactant molecule in an elementary reaction, that step is designated as unimolecular; if there are two reactant molecules, it is bimolecular.80841-78-7. A new synthetic method of this compound is introduced below.

To the flask was added 2000 g of acetone, 160 g of ethyl 4- (1-hydroxy-1-methylethyl) -2-propylimidazole-5-carboxylate (II), 150 g of K2CO3, 460 g of 4- [2- (Trityltetrazol-5-yl) phenyl] benzyl bromide (III), 20g KI, the temperature was raised to reflux, the reaction was incubated for 34-38 hours under stirring.Then add 102g KOH, reflux reaction 6 ~ 8h. Cool to 10 ~ 20 , add 170g DMDO-Cl, incubated for 30 ~ 60min.Heating to reflux, the reaction 22 to 26 hours.After the reaction was added 40g of diatomaceous earth, stirring for 30 to 60 minutes, suction filtration, 200g acetone rinse cake. To the filtrate was added 800g of drinking water and 200g of refined hydrochloric acid, the reaction at room temperature for 2 to 4 hours, filtered to remove by-product triphenylcarbinol. Dropping 10% K2CO3 aqueous solution, adjusting feedstock pH to 4, cooling to 10 ~ 20 , stirring crystallization 2h, filtration, the filter cake with a mixture of pre-cooled 45g acetone and 230g of drinking water washing and drying, to obtain Olmesartan Medoxomil 309 g, total yield 83.1% (relative to ethyl-4- (1-hydroxy-1-methylethyl) -2-propylimidazole-5- carboxylate (II)), purity: 99.27% of the main peak, 0.08% of the olmesartan acid, 0.14% of the triphenylmethanol, and 0.13% of the largest unidentified one.

There are, however, a few established termolecular elementary reactions. The reaction of nitric oxide with oxygen appears to involve termolecular steps.

Reference£º
Patent; Zhejiang Huahai Zhicheng Pharmaceutical Co., Ltd.; Zhejiang Huahai Pharmaceutical Co., Ltd.; Jin Congyang; Wang Jiquan; Zhang Wenling; Wang Peng; (10 pag.)CN107311990; (2017); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

One of the major reasons is to use measurements of the macroscopic properties of a system, the rate of change in the concentration of reactants or products with time, to discover the sequence of events that occur at the molecular level. 80841-78-7, introduce a new downstream synthesis route. 80841-78-7

To a solution of the compound of Formula IV (5.0 g) in toluene (40 mL), dimethylacetamide (10 mL) is added, followed by addition of sodium hydroxide (1.2 g) and N,N-diisopropylamine (3.7 g) at 25-35C. The mixture is stirred at 40- 45C for 4 hours. 5-Methyl-2-oxo-(1 ,3-dioxolene-4-yl)methyl chloride (1.5 g) and tetrabutylammonium bromide (0.5 g) are added at 40-450C. The mixture is stirred at 60-70C for 8 hours. The mass is cooled to 25-35C, water (50 mL) is added, and the pH is adjusted to about 6-7 by adding 10% aqueous HCI. The layers are separated. The aqueous layer is extracted with toluene (25 mL). The organic layers are combined and washed with water (25 mL). The solvent is distilled under reduced pressure. Methanol (25 mL) is added to the residue. The mixture is cooled to 0-50C and stirred at that temperature for 45 minutes. The formed solid is filtered, washed with methanol (10 mL) and dried for 45 minutes under vacuum (yield 3.0 g).

The chemical industry reduces the impact on the environment during synthesis, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; DR. REDDY’S LABORATORIES LTD.; DR. REDDY’S LABORATORIES, INC.; KOLLA, Naveen Kumar; MANNE, Nagaraju; NAREDLA, Anitha; SHINDE, Sachin Gulabrao; WO2011/14611; (2011); A2;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

80841-78-7, A balanced equation for a chemical reaction indicates what is reacting and what is produced, but it reveals nothing about how the reaction actually takes place. The reaction mechanism is the process, or pathway, by which a reaction occurs.80841-78-7. An updated downstream synthesis route of 80841-78-7 as follows.

In 130 ml of N,N-dimethyl acetamide, 14.5 g (20 mmol) of potassium 4-(2-hydroxypropan-2-yl)-2-propyl-1-((2′-(1-trityl-1H-tetrazol-5-yl)biphenyl-4-yl)methyl)-1H-imidazole-5-carboxylate, 3.0 g (2.2 mmol) of potassium carbonate powder and 1.4 g (8.4 mmol) of potassium iodide were added. The mixture was cooled to 0 C and 5.0 g (33 mmol) of 4-(chloromethyl)-5-methyl-1,3-dioxol-2-one was added at 0 to 5C. After the addition, the reaction mixture was warmed to 40-45 C within one hour, then the mixture was stirred at this temperature for 2h. The sample of reaction mixture was analysed (HPLC; tritylolmesartan medoxomil, 97.44%, 4-(2-hydroxypropan-2-yl)-2-propyl-1-((2′-(1-trityl-1H-tetrazol-5-yl)biphenyl-4-yl)methyl)-1H-imidazole-5-carboxylate 0.06 %). The mixture was cooled to 10 to 20C and then 250 ml of ethyl acetate was added. The mixture was cooled again to 5-10 C and then 200 ml of 10% NaCl was added slowly. The temperature should not be higher than 25 C during the addition. The phases were mixed separated and organic phase was washed with 100 ml of 10% NaCl (2*) and dried over anhydrous sodium sulphate. After the filtration filtrate was evaporated under reduced pressure at temperature under 45C to oily residue. To the residue 30 ml of acetonitrile was added at temperature not more than 45C. The mixture was stirred at this temperature for 10 minutes then was cooled to 20 to 25C and stirred at this temperature for 0.5 h and after that 3h at 0 to 5C. The suspension was filtered, washed with cold acetonitrile and dried at 40 to 50C. Yield: 17.0 g (91%) HPLC: 99.64 % of the product, all other impurities under 0.1%. IR: 3408, 1818, 1805, 1741, 1681, 1529, 1148, 1002, 699

This molecular description is the mechanism of the reaction; it describes how individual atoms, ions, or molecules interact to form particular products. The stepwise changes are collectively called the reaction mechanism.

Reference£º
Patent; Krka Tovarna Zdravil, D.D., Novo Mesto; EP2334668; (2011); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem