Day: January 14, 2021

80841-78-7, The molecularity is the number of molecules that collide during that step in the mechanism. If only a single reactant molecule in an elementary reaction, that step is designated as unimolecular; if there are two reactant molecules, it is bimolecular.80841-78-7. A new synthetic method of this compound is introduced below.

1L glass reaction flask was added with 600ml of acetone, 114.8g of intermediate 1 was added with stirring, then 12.8g of sodium hydroxide was added, the temperature was raised to 50-60 C, and the reaction was incubated for 5 hours, and the reaction was monitored by HPLC. To 20-30 C, add 2.8g potassium iodide, 36.0g 4-chloromethyl-5-methyl-1,3-dioxol-2-one, and increase the temperature to 50-60 C after the addition After 1 hour of heat preservation reaction, the temperature was lowered to 20-30 C, filtered, and the filter cake was rinsed with 115 ml of acetone, and the filtrate was combined. The filtrate was concentrated under reduced pressure at 40-50 C until no obvious solvent flowed out, and 320 ml of acetonitrile was added to cool down. The mixture was decanted to 20-30 C for 1 hour, filtered, and the filter cake was rinsed with 320 ml of acetonitrile. The filter cake was blast dried at 40-50 C for 12 hours to obtain a white solid 110.0 g (intermediate 2). The rate was 85.8%, HPLC: 99.2%.

This molecular description is the mechanism of the reaction; it describes how individual atoms, ions, or molecules interact to form particular products. The stepwise changes are collectively called the reaction mechanism.

Reference£º
Patent; Jiashi (Hunan) Pharmaceutical Technology Co., Ltd.; Dai Yongzhi; Liu Hu; Zhu Laifa; Cai Jian; (8 pag.)CN108341804; (2018); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6, The molecularity is the number of molecules that collide during that step in the mechanism. If only a single reactant molecule in an elementary reaction, that step is designated as unimolecular; if there are two reactant molecules, it is bimolecular.144690-92-6. A new synthetic method of this compound is introduced below.

Trityl olmesartan medoxomil (8 g, 10 mmol) is dissolved in THF (50 ml) and 48 % aqueous hydrobromic acid (3.5 ml, 30 mmol) is added. The mixture is stirred for 1 hour at room temperature and then 1 hour at 0 C. The precipitate is filtered, washed with cold THF (20 ml) and dried overnight in vacuum at room temperature to give 5.7 g of olmesartan medoxomil hydrobromide Form B (98.6 % area)

There are, however, a few established termolecular elementary reactions. The reaction of nitric oxide with oxygen appears to involve termolecular steps.

Reference£º
Patent; LEK Pharmaceuticals d.d.; EP2022790; (2009); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

80841-78-7, The molecularity is the number of molecules that collide during that step in the mechanism. If only a single reactant molecule in an elementary reaction, that step is designated as unimolecular; if there are two reactant molecules, it is bimolecular.80841-78-7. A new synthetic method of this compound is introduced below.

Example 2; 36.0 g (50.3 mmol) ethyl 4-(l -hydroxy- 1-methy lethyl)-2-propy 1-1- {4-[2-(trityltetrazol-5-y I)- phenyl]phenyl} -methyl imidazole-5-carboxylate (Va) and 3.0 g (75.4 mmol) of NaOH were suspended in 413 ml dimethylacetamide. The suspension was then stirred at room temperature for 20 h and after that 6.9 g (50.3 mmol) of K2CO3, were added. The mixture was cooled to 00C and solution of 15.4 g (70.4 mmol) 4-chloromethyl-5-methyl-2-oxo-l,3- dioxolene in 39 ml of dimethylacetamide were slowly added. The mixture was slowly heated to 500C and stirred at this temperature for 2 h. After esterification was completed, the mixture was cooled to 10 0C and poured into a mixture of 625 ml of ethyl acetate and 625 ml of 10 % NaCl, and stirred at 25 0C for 15 min. The phases were separated and organic phase was washed 2chi with 500 ml of 10 % NaCl, dried over Na2SO4 and filtered. The filtrate was concentrated up to 14 (approximately 270 g) at reduced pressure.To the resulting solution, 80 ml of ethanol and 8.3 ml (100 mmol) of cone. HCl were added EPO and stirred at 24-26C for 3h. To the cooled mixture 600 ml of water was added and pH of the suspension was estimated to 5 by addition of 5 M NaOH. The phases were stirred for 15 min and separated. Water phase was reextracted with 150 ml of ethyl acetate. Collected organic phases were dried over Na2SO4, filtered and concentrated under reduced pressure. 560 ml of ethyl acetate were added and the mixture was evaporated again. After that, 300 ml of ethyl acetate were added and the mixture was cooled to 20 0C and stirred for Ih, filtered off and washed with 20 ml of fresh ethyl acetate. The yield of the product (I) was 21 g (75 %).

The chemical industry reduces the impact on the environment during synthesis, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; KRKA; WO2007/17135; (2007); A2;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6, A balanced equation for a chemical reaction indicates what is reacting and what is produced, but it reveals nothing about how the reaction actually takes place. The reaction mechanism is the process, or pathway, by which a reaction occurs.144690-92-6. An updated downstream synthesis route of 144690-92-6 as follows.

Example 8; To a solution of (5-Methyl-2-oxo-1,3-dioxolen-4-yl)methyl-4-(1-hydroxy-1-methyl ethyl)-2-propyl-1-{4-[2-(trityltetrazol-5-yl)phenyl]phenyl}methylimidazole-5-carboxylate (5.0 g; 6.25 mmol) and toluene (20 ml) at 15-20 C. is added hydrochloric acid (30 ml). Reaction mass is stirred at 15-20 C. for about 15 minutes to 4 hours. The reaction is monitored by TLC. After completion of reaction layers are separated. Aqueous layer is washed with toluene (10 ml). Adjusted the pH of the aqueous layer to 5-6 using aqueous potassium carbonate solution (200 ml) and the compound is extracted using ethyl acetate (60 ml). Combined ethyl acetate layers are washed with brine. Finally crude product (3.1 g; 89.8%) is isolated by evaporation of solvent under reduced pressure.Purity: 99.5%

With the complex challenges of chemical substances, we look forward to future research findings about Triphenyl methyl olmesartan,belong Dioxole compound

Reference£º
Patent; Ramanjaneyulu, Gorantla Seeta; Mohan, Bandari; Ray, Purna Chandra; Sethi, Madhuresh Kumar; Rawat, Vijendra Singh; Krishna, Yerramalla Raja; Lakshminarayana, Vemula; Srinivas, Mamidi; US2009/281327; (2009); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

An elementary termolecular reaction involves the simultaneous collision of three atoms, molecules, or ions.Triphenyl methyl olmesartan, cas is 144690-92-6. Here is a downstream synthesis route of the compound 144690-92-6, 144690-92-6

A mixture of trityl olmesartan medoxomil in acetic acid and water (1:1, 400 mL) and sulfuric acid (12.2 gm) (1 mol equivalent) was stirred at 25C-30C for 45-60 minutes. Triphenylcarbinol was filtered and the filtrate was washed with acetic acid and water mixture (1:1, 50 rnL). Sodium carbonate solution (25% w/v, 100 mL) was charged to the filtrate and the product was extracted with dichloromethane (500 mL) followed by recovery of the solvent. The product was isolated, recrystallized using acetonitrile (300 mL), filtered, washed and dried under reduced pressure to obtain crude olmesartan medoxomil.Yield: 90% HPLC purity: 99.29 % OLM-acid: Not Detectable OLM- Eliminate: 0.07% Acetic acid content: Not Detectable

A chemical reaction often occurs in steps, although it may not always be obvious to an observer.

Reference£º
Patent; RANBAXY LABORATORIES LIMITED; KAPOOR, Ashwini, Kumar; MEHTA, Hiten, Sharadchandra; NATH, Asok; PRASAD, Mohan; WO2010/134052; (2010); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

Rate laws may be derived directly from the chemical equations for elementary reactions. This is not the case, however, for ordinary chemical reactions.37830-90-3, molecula formula is 4,5-Dimethyl-1,3-dioxol-2-one, below Introduce a new synthetic route., 37830-90-3

Example 1The feeding substance than the molar amount of the: DMDO: sulfonyl chloride to 1 : 1.3. The organic solvent is dichloromethane, the quality of the organic solvent with DMDO volume ratio is 1:7. Solid free radical scavenging agent is methyl hydroquinone, DMDO the quality of the amount of 1percent.To is provided with a magnetic stirring, constant pressure dropping funnel, reflux condensation tube, thermometer and is provided with a tail gas absorption device 500 ml flask to three in 350 ml dichloromethane, 50gDMDO, under stirring backflow state, slowly dropping 77g sulfonyl chloride, dropping time is approximately 2.5h, heat preservation after dropping 2h, rotary evaporation to remove the solvent. Furthermore, added to the bottoms of 0.5g methyl hydroquinone, for 90 ¡ãC conditions, stirring rearrangement 5h, obtaining a reaction crude. Analysis of the purity of crude 92.33percent, the crude in 2mmHg the vacuum degree of the vacuum distillation, to obtain the target product 52.8g, to yield 81.1percent, purity of 97.87percent.

Elementary reactions that involve the simultaneous collision of more than three molecules are highly improbable and have never been observed experimentally.

Reference£º
Patent; Six Anke Rui Da New Materials Co.,Ltd.; Bao, Yuanzhi; Weng, Shibing; Zhao, Zhongyao; (6 pag.)CN105348249; (2016); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6, A balanced equation for a chemical reaction indicates what is reacting and what is produced, but it reveals nothing about how the reaction actually takes place. The reaction mechanism is the process, or pathway, by which a reaction occurs.144690-92-6. An updated downstream synthesis route of 144690-92-6 as follows.

78(b) (5-Methyl-2-oxo-1,3-dioxolen-4-yl)methyl 4-(1-hydroxy-1-methylethyl)-2-propyl-1-{4-[2-(tetrazol-5-yl)phenyl]phenyl}methylimidazole-5-carboxylate 75 ml of water were added to a suspension of 29.3 g of (5-methyl-2-oxo-1,3-dioxolen-4-yl)methyl 4-(1-hydroxy-1-methylethyl)-2-propyl-1-{4-[2-(trityltetrazol-5-yl)phenyl]phenyl}methylimidazole-5-carboxylate [prepared as described in step (a) above] in 225 ml of acetic acid, and the resulting mixture was stirred at 60 C. for 1.5 hours. At the end of this time, 75 ml of water were added to the mixture, which was then cooled. Precipitated trityl alcohol was removed by filtration, and the filtrate was concentrated by evaporation under reduced pressure. Toluene was added to the residue, and the mixture was again concentrated by evaporation under reduced pressure, to remove the remaining water and acetic acid. The residue was crystallized in ethyl acetate, to give 16.6 g of the title compound as crystals, melting at 177-180 C. (with decomposition). The Nuclear Magnetic Resonance Spectrum of this compound was identical with that of the compound obtained as described in Example 61(b).

A chemical reaction often occurs in steps, although it may not always be obvious to an observer.

Reference£º
Patent; Sankyo Company, Limited; US5616599; (1997); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6, A balanced equation for a chemical reaction indicates what is reacting and what is produced, but it reveals nothing about how the reaction actually takes place. The reaction mechanism is the process, or pathway, by which a reaction occurs.144690-92-6. An updated downstream synthesis route of 144690-92-6 as follows.

A solution of MTT in an organic solvent and water (20%) was heated for 4-8 hrs at reflux. When the solvents were either acetonitrile (ACN), isopropyl alcohol (IPA) or t-butanol (t-BuOH), 1 volume of water was added, and the reaction was stirred until the amount of MTT was less than 2%. The mixture was evaporated to dryness. Ethyl acetate (EtOAc, 1 volume) was added to the residue and then evaporated again (twice). The resulting solid was dissolved in EtOAc (12 vol) and heated to reflux. The solution was cooled (2 C.) and stirred for 2 hrs. The product was filtered, washed (EtOAc, 1 vol), and dried on vacuum (45 C.). Table 1 shows the process details with different organic solvents: TABLE 1 Total solvent Time Solvent(s) Volume Temperature ( C.) (hrs) pH ACN:H2O 5:1 + 1 85 7 4.89-4.3 IPA:H2O 5:1 + 1 85 7 4.62-4.25t-BuOH:H2O 5:1 + 1 85 7 4.78-4.28n-propanol:H2O 5:1 reflux 2.5 4.3n-BuOH:H2O 5:1 110 2.5 4.412-BuOH:H2O 5:1 100 3 4.5iso-penthanol:H2O 5:1 100 3 5DMA:H2O 5:1 100 4 4.5DMF:H2O 5:1 100 4 4.5, 144690-92-6

As the rapid development of chemical substances, we look forward to future research findings about 144690-92-6

Reference£º
Patent; Hedvati, Lilach; Pilarsky, Gideon; Shenkar-Garcia, Natalia; US2006/148870; (2006); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

An elementary termolecular reaction involves the simultaneous collision of three atoms, molecules, or ions.Triphenyl methyl olmesartan, cas is 144690-92-6. Here is a downstream synthesis route of the compound 144690-92-6, 144690-92-6

One hundred ml of methanol was added to 10 g of (5-methyl-2-oxo-l,3-dioxol- 4-yl) methyl 4-(2-hydroxypropan-2-yl)-2-propyl-l-((2′-(l-trityl-lH-tetrazol-5-yl) biphenyl-4-yl) methyl)-lH-imidazole-5-carboxylate (Pharmacostech). Then to the reaction mixture was added 10 g of resin pre-treated with hydrochloric acid of pH 2-3 (TRILUE SCR-IO gel type), followed by refluxing for 6 hours. The solid components were filtered out from the reaction mixture and washed with 100 ml of methanol. The solid substance obtained by vacuum distillation of the filter-in solution was dissolved into a small quantity of acetone, and n-hexane was added to the acetone solution to obtain 6.58 g (yield rate: 94%) of the standard compound represent by Formula 9: 1H NMR (300 MHz, DMSO), delta 7.50-7.69 (m, 4H), 7.03 (d, 2H, J=8.0 Hz), 6.85 (d, 2H, >8.0 Hz), 5.41 (s, 2H), 5.22 (s, IH), 5.05 (s, 2H), 2.50 (s, 2H), 2.07 (s, 3H).

A chemical reaction often occurs in steps, although it may not always be obvious to an observer.

Reference£º
Patent; PHARMACOSTECH CO., LTD.; KIM, Jae Won; CHA, Young Gwan; RYU, Hyung Chul; KIM, Sun Joo; WO2010/67913; (2010); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6, The molecularity is the number of molecules that collide during that step in the mechanism. If only a single reactant molecule in an elementary reaction, that step is designated as unimolecular; if there are two reactant molecules, it is bimolecular.144690-92-6. A new synthetic method of this compound is introduced below.

To TOLM (75 g) were successively added acetic acid_water=1:1 (330 mL, 4.4 vol) and concentrated sulfuric acid (5.4 mL, 1.08 eq). The obtained mixture was stirred at 25C – 30C for 1 hr. Using TLC (thin layer chromatography) (TLC eluent: 10% methanol/methylene chloride, detection method: UV), complete disappearance of TOLM was confirmed. [0309] The reaction mixture was filtered and insoluble trityl alcohol was removed. The aqueous layer was adjusted to pH 2 – 3 by adding 25% aqueous sodium carbonate solution (initial pH of the reaction mixture was 4 – 4.5). The reaction mixture was stirred for 5 min, methylene chloride (225 mL, 3 vol) was added thereto, and the mixture was stirred for 5 min. Stirring was stopped, and the mixture was stood and partitioned. The aqueous layer was extracted with methylene chloride (2×225 mL, 2×3 vol), the extracts were combined with the organic layer, deionized water (375 mL, 5vol) was added, and the mixture was stirred for 5 min. Stirring was stopped, and the mixture was stood for 5 min and partitioned. To the organic layer was added saturated brine (375 mL, 5 vol), and the mixture was stirred for 5 min, left standing and partitioned. The organic layer was concentrated under reduced pressure at 40C – 45C to give crude OLM MDX (49 g, 93%) as a pale-yellow solid.To the crude OLM MDX (49 g, 1 eq) obtained in the above-mentioned (7) was added acetone (735 mL, 15 vol), and the mixture was stirred at 55C – 60C for 10 min. Furthermore, the reaction mixture was stirred at the same temperature for 15 min, and acetone was evaporated under normal pressure. Heating was stopped when a solid was precipitated, and the mixture was cooled to 25C – 30C. The precipitated solid was collected by filtration and dried with suction for 30 min to give OLM MDX (41 g, 83%). [0311] To the OLM MDX obtained above was added isopropyl alcohol (164 mL, 4 vol), and the mixture was heated to 55C – 60C, and stirred at 55C – 60C for 1 hr. Heating was stopped and the mixture was gradually cooled to 25C – 30C, and stirred at 25C – 30C for 30 min. The precipitated solid was filtered and dried with suction to give OLM MDX (41 g, 100%). [0312] The OLM MDX (41 g) obtained above and acetone (about 1 L) were heated to 55C – 60C, and stirred at 55C – 60C for 25 min. Acetone was evaporated under normal pressure until the mixture became cloudy, and the mixture was gradually cooled to 25C – 30C. The precipitated solid was collected by filtration and dried with suction for 30 min to give OLM MDX (34 g, 83%). The HPLC purity of the obtained OLM MDX was 99.66%. [0313] The OLM MDX (44 g) obtained above was dissolved in acetone (about 1.2 L), and the mixture was stirred at 55C-60C for 10 min. Acetone was evaporated under normal pressure until the solution became cloudy, and the solution was gradually cooled to 25C – 30C. The precipitated solid was collected by filtration, dried with suction for 30 min, blast dried for 1 hr, and further blast dried at 40C – 45C for 5 hr to give OLM MDX (36 g) as a white solid. The HPLC purity of the obtained OLM MDX was 99.8%.

The chemical industry reduces the impact on the environment during synthesis, Triphenyl methyl olmesartan, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; API Corporation; SEKI, Masahiko; EP2891650; (2015); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem