Month: September 2020

144690-92-6, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”144690-92-6

To the three-necked flask were added with 38 ml of ethyl acetate, 45 g of 6.4% dilute hydrochloric acid, 25 g of trityl olmesartan medoxomil was added with stirring. Stir in water bath, control the temperature 15 to 20 C, stirring about 4 hours, TLC plate detection point of raw material disappeared,That is, it is judged that the deprotection reaction is completed.Cooled to room temperature, 115 ml * 5 toluene was added to wash, the aqueous layer was added with 135 ml of acetone, potassium bicarbonate aqueous solution adjusted P=4.0, control temperature 15 ¡À 5 C Stir for 2 hours, Filtered and dried to give 16.0 g of olmesartan medoxomil in a yield of 90.2%. HPLC analysis: purity 98.75%, impurity a (olmesartan acid) 0.71%, individual impurities less than 0.10%

144690-92-6 is used more and more widely, we look forward to future research findings about Triphenyl methyl olmesartan

Reference£º
Patent; Zhejiang Huahai Pharmaceutical Co., Ltd,; Huang, Xiangliang; Zhang, LI; Hua, yuanyuan; Wu, Yong De; (7 pag.)CN102584804; (2016); B;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”144690-92-6

Trityl olmesartan medoxomil (260 gm) as obtained in example 1 was dissolved in toluene (2600 ml) and then added concentrated hydrochloric acid (156 ml) for 1 hour minutes at room temperature. The reaction mass was maintained for 1 hour 30 minutes at room temperature and then added water (1000 ml). The reaction mass was stirred for 45 minutes at room temperature and the layers were separated. To the aqueous layer was added ethyl acetate (5000 ml) at room temperature. The reaction mass was cooled to 15 to 20 C. and pH of the reaction mass was adjusted to 4.5 to 5.5 with sodium carbonate (20%, 560 ml). The reaction mass was stirred for 20 minutes at 20 C. and the layers were separated. The organic layer was dried over sodium sulfate and ethyl acetate was distilled off completely under vacuum at below 45 C. to obtain a residual mass. To the residual mass was added ethyl acetate (400 ml) at 40 C. and then heated to 75 to 80 C. The contents were maintained for 30 minutes at 75 to 80 C. The reaction mass was cooled to room temperature and stirred for 1 hour. The reaction mass was further cooled to 10 to 15 C. and stirred for 1 hour 30 minutes, filtered. The solid obtained was dried at 40 to 45 C. for 4 hours to obtain 150 gm of olmesartan medoxomil. Olmesartan medoxomil: 98.6%; Olmesartan acid impurity: 0.32%; Trityl olmesartan medoxomil impurity: 0.35% Methyl olmesartan medoxomil impurity: 0.35%.

The chemical industry reduces the impact on the environment during synthesis, Triphenyl methyl olmesartan, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; HETERO RESEARCH FOUNDATION; Parthasaradhi Reddy, Bandi; Rathnakar Reddy, Kura; Muralidhara Reddy, Dasari; Raji Reddy, Rapolu; Ramakrishna Reddy, Matta; Vamsi Krishna, Bandi; US2013/190506; (2013); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”80841-78-7

Example 96.20 g of (III) were suspended in a mixture of 15.5 ml of tetrahydrofuran:dimethyl sulfoxide (2:3, v/v). The mixture was cooled to 17C in order to add 0.45 g (1.3 equivalents) of sodium hydroxide. The mixture was then heated to 60C. After two hours 1 .55 g (1 .1 equivalents) of potassium carbonate were added to the mixture. The mixture was heated to 70C and 1 .41 g of (IV) dissolved in 16.2 ml of tetrahydrofuran were added to the mixture over 1 .5 hours. The reaction was completed in one hour. The mixture was cooled to room temperature. The mixture was then washed three times with a 29% solution of sodium chloride in water. Finally, the organic solvent was distilled and 18.6 ml of ethyl acetate were added. Finally (V) was crystallised from ethyl acetate by cooling. The mixture was cooled to 0-5C, it was filtered, washed with ethyl acetate and heptane and the resulting solid was dried in a heat cabinet. 5.54 g of (V) were obtained (80% yield). The resulting solid was analysed by HPLC, showing a purity of more than 97%.

The chemical industry reduces the impact on the environment during synthesis, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; INTERQUIM, S.A.; JOVE MARTI, Iban; MARQUILLAS OLONDRIZ, Francisco; WO2012/55994; (2012); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”80841-78-7

10L autoclave, 520g (0.75mol) Compound 5, DMF3kg, potassium carbonate and 215.3g (1.6mol), stirred at room temperature 1.5-2.5h added to the system after 63.0g (0.38mol) of potassium iodide was added dropwise while – Chloromethyl -5-methyl-1,3-dioxol-2-one 40.0g (0.94mol). Dropping was completed, the reaction at room temperature after 3-4h TLC or HPLC in control, raw reaction was complete. To the system was added ethyl acetate and 3L 3L water and 200g of sodium chloride, stirring separated and the aqueous layer was washed with 3X1L ethyl acetate, the combined organic layers, the organic layer was dried, filtered and the solvent was evaporated cooling is added 0-10 , methanol was added 1600g beating 30min, filtered, then the filter cake was slurried at room temperature in acetonitrile 1600g 30min, filtered to afford intermediate 6 about 553.8g,

The chemical industry reduces the impact on the environment during synthesis, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; Jiangsu Bang Pharmaceutical Co., Ltd.; Zhao, Guangrong; Huan, Shuang; Zhao, Huayang; Liu, Liping; Chen, Guoping; Tang, Jingyu; (19 pag.)CN105481842; (2016); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”144690-92-6

A solution of MTT in an organic solvent and water (20%) was heated for 4-8 hrs at reflux. When the solvents were either acetonitrile (ACN), isopropyl alcohol (IPA) or t-butanol (t-BuOH), 1 volume of water was added, and the reaction was stirred until the amount of MTT was less than 2%. The mixture was evaporated to dryness. Ethyl acetate (EtOAc, 1 volume) was added to the residue and then evaporated again (twice). The resulting solid was dissolved in EtOAc (12 vol) and heated to reflux. The solution was cooled (2 C.) and stirred for 2 hrs. The product was filtered, washed (EtOAc, 1 vol), and dried on vacuum (45 C.). Table 1 shows the process details with different organic solvents: TABLE 1 Total solvent Time Solvent(s) Volume Temperature ( C.) (hrs) pH ACN:H2O 5:1 + 1 85 7 4.89-4.3 IPA:H2O 5:1 + 1 85 7 4.62-4.25t-BuOH:H2O 5:1 + 1 85 7 4.78-4.28n-propanol:H2O 5:1 reflux 2.5 4.3n-BuOH:H2O 5:1 110 2.5 4.412-BuOH:H2O 5:1 100 3 4.5iso-penthanol:H2O 5:1 100 3 5DMA:H2O 5:1 100 4 4.5DMF:H2O 5:1 100 4 4.5

The chemical industry reduces the impact on the environment during synthesis, Triphenyl methyl olmesartan, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; Hedvati, Lilach; Pilarsky, Gideon; Shenkar-Garcia, Natalia; US2006/148870; (2006); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact.37830-90-3, 4,5-Dimethyl-1,3-dioxol-2-one it is a common compound, a new synthetic route is introduced below.37830-90-3

Step III: 4-Bromomethyl-5-methyl~l,3-dioxol~2-one; A mixture of 4,5-dimethyl-l,3-dioxol-2-one (1.5 g, 0.013158 mol), NBS (2.34 g, 0.013158 mol) and benzoyl peroxide (0.089 g, 0.0003684 mol) in CCl4 (20 mL) was stirred at 77¡ãC for 6 hrs (TLC monitoring: cyclohexane/AcOEt 6:4). The solution was treated with an aqueous solution OfNaHCO3 and extracted with CH2Cl2. The organic phase was dried over Na2SO4 and concentrated under reduced pressure to give 4-bromomethyl-5 -methyl- 1,3- dioxol-2-one (2.34 g). Yield: 92percent.1H-NMR (400 MHz, CDCl3, delta): 2.13 (s, 3H, CH3), 4.18 (s, 2H, CH2Br).

Chemical properties determine the actual use. Each compound has specific chemical properties and uses. We look forward to more synthetic routes in the future to expand 4,5-Dimethyl-1,3-dioxol-2-one reaction routes.

Reference£º
Patent; S.I.M.S. S.r.l. – SOCIETA ITALIANA MEDICINALI SCANDICCI; WO2008/12852; (2008); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”144690-92-6

A solution of MTT in an organic solvent and water (20%) was heated for 4-8 hrs at reflux. When the solvents were either acetonitrile (ACN), isopropyl alcohol (IPA) or t-butanol (t-BuOH), 1 volume of water was added, and the reaction was stirred until the amount of MTT was less than 2%. The mixture was evaporated to dryness. Ethyl acetate (EtOAc, 1 volume) was added to the residue and then evaporated again (twice). The resulting solid was dissolved in EtOAc (12 vol) and heated to reflux. The solution was cooled (2 C.) and stirred for 2 hrs. The product was filtered, washed (EtOAc, 1 vol), and dried on vacuum (45 C.). Table 1 shows the process details with different organic solvents: TABLE 1 Total solvent Time Solvent(s) Volume Temperature ( C.) (hrs) pH ACN:H2O 5:1 + 1 85 7 4.89-4.3 IPA:H2O 5:1 + 1 85 7 4.62-4.25t-BuOH:H2O 5:1 + 1 85 7 4.78-4.28n-propanol:H2O 5:1 reflux 2.5 4.3n-BuOH:H2O 5:1 110 2.5 4.412-BuOH:H2O 5:1 100 3 4.5iso-penthanol:H2O 5:1 100 3 5DMA:H2O 5:1 100 4 4.5DMF:H2O 5:1 100 4 4.5

With the complex challenges of chemical substances, we look forward to future research findings about Triphenyl methyl olmesartan

Reference£º
Patent; Hedvati, Lilach; Pilarsky, Gideon; Shenkar-Garcia, Natalia; US2006/148870; (2006); A1;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”80841-78-7

A solution containing about 46 g of compound 4 was taken, 3.5g sodium iodide was added, 280 mL N, N-dimethylformamide, 11.2g DMDO-Cl was slowly added dropwise, 30 Minute addition is completed. After dropping, Heated to 55 , Reaction for 7 hours, The reaction is completely over. filter, Remove insolubles, The filtrate was poured into 700mL of water, Extraction with ethyl acetate, The ethyl acetate layer was collected, dry, filter, The filtrate is concentrated. To the oily substance obtained after the concentration was added 200 mL of ethanol, Stirring, A white solid precipitation, Collect the solid, Washed with 50mL cyclohexane beating, 45.0 g of product was obtained, Two-step total yield of 80.6% The purity of the product was 98% by HPLC.

The chemical industry reduces the impact on the environment during synthesis, 4-(Chloromethyl)-5-methyl-1,3-dioxol-2-one, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; Disha Pharmaceutical Group Co., Ltd.; Zhang Zhaoxing; Zhang Hongqiang; Qin Litai; Li Wei; Li Zongwen; Xia Haijian; (6 pag.)CN103012382; (2016); B;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”144690-92-6

7.5 cm in diameterIn a 500 mL four-necked flask equipped with two stirring blades,40 g of trityl olmesartan medoxomil,180 ml of acetic acid,40 g (1.0 volume) of water was added,The mixture was stirred at 40 C. for 2 hours to carry out deprotection reaction (reaction conversion: 98.4%Olmesartan medoxomil purity: 98.95%,Olmesartan dimer: 0.047%).Then,The reaction solution was cooled to 20 C.,80 g of water was added,After stirring at 20 C. for 1 hour,The precipitated triphenylmethanol was removed by vacuum filtration,To the obtained filtrate, 240 ml of 10% sodium hydrogen carbonate was added,The liquidity of the aqueous layer was adjusted to pH 3.5,After adding 400 ml of ethyl acetate and vigorously stirring,The aqueous layer was separated,An organic layer containing olmesartan medoxomil was obtained (olmesartan medoxomil purity: 99.35%Dimer: 0.011%).200 ml of ethyl acetate was distilled off from the organic layer,After stirring at 20 to 30 C. for 1 hour,The precipitated solid was collected by filtration under reduced pressure as a wet body.The obtained wet body was dried at 40 C. for 14 hours,24 g of crystals of olmesartan medoxomil were obtained (yield: 86%, olmesartan medoxomil purity: 99.71%, dimer: 0.010%).

The chemical industry reduces the impact on the environment during synthesis, Triphenyl methyl olmesartan, , I believe this compound will play a more active role in future production and life.

Reference£º
Patent; Tokuyama Corporation; Mori, Hiroshi; Tanaka, Kenji; (12 pag.)JP6091339; (2017); B2;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem

144690-92-6, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route.”144690-92-6

10L reaction flask was charged 500.0g (0.62mol) compound 6,3L water, 1L of acetone, was added dropwise a solution of 645.0g of 22.5% sulfuric acid at 20 . Dropping was completed, the reaction at room temperature after 4.5h TLC or HPLC in control, raw reaction was complete. Body cooling system to 0-5 , when the temperature stabilized filtrate back into the reaction vessel was charged with acetone 1L and 2L water. The system was maintained at 15 solution of 210g of potassium carbonate and 400g water to form a solution, drops of completion, stirring after 1-2h incubation filtration. The filter cake was dried to obtain olmesartan medoxomil pure 328.9g. HPLC: 99.96%, yield: 94.3%, 144690-92-6

As the rapid development of chemical substances, we look forward to future research findings about 144690-92-6

Reference£º
Patent; Jiangsu Bang Pharmaceutical Co., Ltd.; Zhao, Guangrong; Huan, Shuang; Zhao, Huayang; Liu, Liping; Chen, Guoping; Tang, Jingyu; (19 pag.)CN105481842; (2016); A;,
1,3-Benzodioxole – Wikipedia
Dioxole | C3H4O2 – PubChem